Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello:
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
I know this pin is used in QSPI even after disabling the QSPI I am unable to toggle the GPIO what is the reason.
And this the sane pin I'm using for I2C that's not working...
Seeing the failure below and wondering a couple things:
How did the device get into this state?
How do I disable AP protection? The Kconfig GUI seems to indicate that...
Hi all,
We are testing with the nrf9151 (mfw 202) on custom hardware with an external active antenna (molex 206640) and a slightly altered SLM (from SDK 2.7.0). Most important...
Hi all,
I'm working with the nRF9160 DK and running the AWS IoT sample from the nRF Connect SDK v2.7.0 ( 5cb85570ca43 ). The device connects to the network and AWS IoT Core...
Hi,
I want to add scheduler server to the mesh/light sample with nrf52DK, I change the element define like below:
static struct bt_mesh_elem elements [] = {
BT_MESH_ELEM...
Hello, I am experiencing issues with the current measurements taken by the PPK2 when using the nPM2100-EK to power a device. The current drawn from the 2.7V power source ...
Hi Nordic team,
We are planning to use the STM32H747 as the host MCU to control the nRF7002 for Wi-Fi functionality. Based on reference materials and existing use cases...
Project (NCS v2.7.0):
We are working on an application that requires time synchronized sampling of sensor data from 4 nRF52840 devices. The sensor data is then streamed...
When we were using nrfjprog to flash, we used "west flash --erase" because it was quicker to erase entire flash then sector by sector. However, when we upgraded to SDK 3.0...
In the specs of npm1300 PS, it is suggested that the ADC can measure VBAT, VBAT_7V range, NTC, DIE_TEMP, VSYS, IBAT. However, in the interrupt configuration reported in 7...
Hello,
I've inherited a project to create an iOS app that can communicate via BLE to UART RS232 to devices in the field using a proprietary protocol and at 115200 baud and...
Hello,
I am having nRF9160 with modem FW = 1.3.6 and nrf sdk version 2.7.0
I am using MBEDTLS library for generating self-signed & CSR certificates with EC-Key and RSA...
Use API: k_thread_state_str() to get the status of the thread, but I don't know the length and content of the obtained string. I want to understand this part.I want to query...
Hi, I am using nrf52840-based custom hardware and have an external flash connected on SPIM3. Till now I was working with my other peripheral connected on different buses and...