Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi,
I use the SDK12.3 and SD130 with secure_bootloader and my own application. I can flash SD and Bootloader and update my app over OTA with DFU from NRF Toolbox. My app...
I noticed that when upgrading to the latest Thread SDK that my devboard stopped booting. I was following the instructions as per the documentation but noticed that my user...
Hi,
I am designing a custom PCB using the nRF51422. I want to include an external 16 MHz crystal oscillator to use as X1 according to the reference layout for custom PCBs...
When I test the timer example with nrf52832 DK, it so nice to 4 minutes.
uint32_t time_ms = 240000;
But when I set the time interval over 5 minutes, then the event...
What is the maximum number of bond table entries a device can have?
If a device allows only one connection to be established at once (not more than one simultaneously)...
Hi,
I want to store the CRC of the current firmware in the flash, for DFU purposes. Almost all of the threads I've seen so far reference the pstorage API but it's no longer...
I am searching for a basic example to understand the build system.
How do I load the soft device properly?
How do I set things up to run SEGGER_RTT_WriteString?
I...
I am using Nrf52832 sdk 11.I want to update the value of characteristic on every read operation from my andriod phone. I want that on every ble_gatts_evt_read: should give...
Hi! Im trying to figure out the power consumption of two types of beacons that uses nRF51 and nRF52. I have connected a small resistor in between the supply and measuring...
Preferrably under linux using gcc and the command prompt.
I am most interested in project setup, loading the soft device, and making sure all the core systems are working...
I am running the ble_app_uart example in SDK 13.0 with nRF52382.
First issue
The app can receive data via UART only when I use "Termite" as a terminal emulator...
Hi, trying to implement timeslot api and stuck with TIMER0.
I saw similar questions but answers is still unclear.
My timer init code:
NRF_TIMER0->MODE = TIMER_MODE_MODE_Timer;...
Hi
I am using nrf52832 with softdevice s132_nrf52_3.0.0.
In my appliocation I need to do periodic measuremets, and it is critical that softdevice doesn't interrupt during...
Hi,
I have to make a interrupt each 100us. This interrupt should be priority on the BLE. In my interrupt I have only one condition (if/else) and I have to change PWM value...
