I am working with NRF52840 with SoftDevice S140 and SDK v17.1.0.
The boot loader address for this chip is 0xF8000. I can set up one of the 'fstorage' module with the address...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hello!
I'm in doubts about proper configuration of GPIO pin, which I'd like to be able to reset external device (DWM1000), connected to nRF51 by SPI.
The datasheet says...
Hello,
I’m working on my own custom board based on the nrf52832 (QFAABB).
Here the schematic:
I succeed to flash the board with the nrf52DK (PCA10036) via the debug...
Hi there - new to Bluetooth but have an interesting question.
Is there a way to have multiple users connected to the same Bluetooth connection to stream music? For instance...
Hi community,
I am working on IoT device. We want to establish a secure connection therefore we are going to need a secure storage for our private key. I am aware that the...
Worked fine until yesterday. Board turned off with computer, also the power switch on the board was in off position before turned on this morning. Now the debugger circuit...
Hello Nordic Team,
Please, I would like to ask some questions about BLE based smart-phone accessory.
Actually, I think about using a BLE based accessory (for instance...
Tuning the nRF24xx matching network:
The balun-function is done by the
180° degrees phase shift in L1. This
causes the signals from the two ANT
pins, 180° out of...
I am sending IMU data as 20 byte packets through nus service at the rate of 50 such packets per second. The device is a nrf51 DK configured as ble peripheral (S110). The application...
Hi all,
I have a makefile which runs perfectly from the command line on Windows under GCC, but in Eclipse it fails with this message in the Console:
make flash
make...
My application had a ID to separate difference device & host for the communication in the same area. When the Host power up, it need to search any existing same ID Host nearby...
Hi ,
I want to set the channels used for exchanging DATA (after connection) when peripheral and master are connected.
i searched and i find that it's like this :
//Set...
Hi I'm using the PCA10003 dev board to try it out the OTA firmware update.
What i did is exactly that:
Modify the bootloader example for S310 softdevice and 10003...
Hi, I have been developing with the nRF52 DK for the past couple of months however I have encountered an issue today which I am unable to resolve.
I am unable to establish...
Continuing my mission to have SES set up to be the complete development environment on a Mac I am struggling to get the Jlink Debugger to behave with SES.
It appears I...
hello , I want to Know how to write value to S0 , L ,S1.
for example : I want Set S0 =1 , L = 16 , S1 = 1 .
but I can't find any register to set S0 , L , and S1. .
My...
