I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
The assert in the function below breaks the functionality when reliable is set to false (e.g. non SoftDevice code). It exists in (at least) SDK10 and SDK11.
Remove the assert...
Hello,
I'm a beginner in IOT and Nordic products.
I followed the steps given in the tutorials given by the Nordic developer zone and made the SDK act as central/peripheral...
Hi,
In my application I need radio notification only during connection. When connection is dropped the peripheral goes to advertising mode and here i disable the radio...
Hi all again guys! I am experiencing a problem with my application: i have a beacon that is sending ADC converted values to a nrf51 DK (via notification), which is connected...
Hello,
I want to use SPI between one nRF51-DK (using SD130 v 2 and SDK11) and another board. I am supplying the nRF with 2.3 V and initializing the BLE and the SPI. I can...
I have a BLE application in mind in which it would be useful for the BLE server to obtain the battery level of the BLE client (in this case, a phone, laptop, or tablet). I...
Hi,
Is Nordic looking to support mbed OS on the nrf51/nrf52 series chips?
Currently it looks like the best supported platform is the mbed Classic SDK, but it looks like...
Hi,
I am trying to make a program for the NRF51 development kit on mbed. I have been able to take ADC samples at 1000Hz which is what I want, but I can't seem to print...
In SDK 11 description od DTM "vendor specific" settings, there is a lot of inconsistency in parameters names/numbers - could anyone help me understand this part?
As for...
Hi,
Everyone,
I have firmware working with our custom pcbs.
It works fine with new 3.3v battery.
But somehow it does not advertise anything with used battery having...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
I guess we need some help with definitions. Basically, we'd like to read data from an I2C line. Should be as simple as "set to input" and "read the pin". However...
In...
Using nRF5 SDK v11.0.0, I am working on bringing up new hardware based on the nRF52. I started with code that works on the PCA10040 development board in which we connected...
