dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hello, a quick rundown on the problem here:
New versions of Softdevices S140 corrected an error and now correctly ignores writing to cccd descriptor using write instead...
I have 4 devices communicating in a Bluetooth piconet, where 1 device is the master device and 3 devices are slave devices.
I want to time synchronize the 4 devices to...
Hi,
I'm using the S132 v3 and wonder about the impact of DLE on scheduling.
In the chapter on Scheduling in the softdevive specification is writen that multiple peripherals...
I would like to setup the just released RasPI demo using the Nordic-Thingy52-Nodejs repo
I don't have a dongle, but 4 PDK 52840 boards and 2 Thingys.
Can I still use 1...
I found that blindly configuring all GPIO pins can stop the LFXO and RTC counter. I am reporting this as: something to be aware of, not obvious to everyone. Not a question...
I am testing the nRF52832 in Rigado BMD-301 module. I am able to get to ~40uA when advertising ,UART enabled but not used and all other peripherals disabled. But as soon as...
I connect to my BLE peripheral device using NRF connect app. While in connection, if I switch my phone's bluetooth off and turn it back again and then try to connect to my...
Hi!
I'm using the nrf52 on custom prototype boards and the official development boards. We are using the ADC to read analog values and encountered unexpected behavior related...
Starting notification and then writing 0x01 to the control point
does not cause the Buttonless DFU to enter boot mode. LED #1
remains on.
Run time trace show:
APP...
The Problem ist the continuous sending of Byte-Arrays with spi and fixed sample rate.
Strategie:
Send Array-List with XFER triggered by Timer (every 3ms) and auto increment...
Hello,
I bought Nrf 52832 breakout board .
Actually i want to measure the current consumption of chip as we want to use it.
While advertising 26 bytes it consume really...
I have questions about the HCI packet format
With the start packet, the Ack number in the header section = 000
What should it be filled in the data packet and...
I'm implementing an I2C communication and I need to set an interruption every time the sensor sets the interrupt pin to 0. I've been checking some other posts from devzone...
Hello,
I am currently trying to power profile all aspects of the nRF52840, which includes the CryptoCell 310. The instructions say "
Testing
Test the CryptoCell Example...
