Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
Hi,
NRF54L15, nordic sdk version 2.9.1
I recently lost ability to build my application. I get this linker error:
/home/adam/ncs/toolchains/b77d8c1312/opt/zephyr-sdk...
Hello,
Now, I currently run Asset_Tracker_Template on Thingy91X
https://github.com/nrfconnect/Asset-Tracker-Template/blob/main/docs/common/getting_started.md.
And, I...
Hi,
I have autoprovisioned and autoconfigured my nrf52840 board (provisioning and configuring are made inside the software and not through external app/provisioner).
In...
Hello Nordic Team,
Currently, we are performing power consumption testing using the Nordic nRF54L15-DK development kit.
As part of this, I aim to fully disable the Radio...
I do not use board.h nor bsp* in my project, and also I am not initializing the pins that I do not use in my program currently - so P0.17 is not initialized and setup. However...
Hi all,
I am new to nrf51-dk and I am using nRF5 SDK v11.0.0.
I wanted to perform the task below.
When the DK is turned ON, read on board push button status.
If button...
We are implementing scan functionality in nRF51. I would like to understand if anyone has tested or tried to scale this functionality when there are thousands of beacons around...
Hi everyone,
I was wondering how GAP calls and events are synchronized within the SoftDevice.
Example:
// conn_handle is updated in the CONNECTED and DISCONNECTED...
The Android Master Control Panel app has an option to remove bond information (which works). But the API for it is hidden .
I'm just wondering if you use reflection to...
We are trying to replace an existing solution that uses a custom Service with 4 Characteristics. Unfortunately none of those share the same base UUID.
Basically the Service...
Ok - I'm trying to get my arms around this bootloader process.
I am using the nRF5_SDK_11.0.0_89a8197 SDK along with the PCA10040 develeopment kit.
I also am using IAR...
I'm trying the run the smart remote 3 v1.1 firmware built using IAR.
The firmware fails to init the touchpad and enters a forever loop.
The program only builds with optimization...
Hi,
I am using nRF52832 with S132_V2.0.0 and SDK_11.0.0. In my application i plan to use RFX2411N PA/LNA module. In datasheet of RFX2411N, I found that it can be used in...
Trying to qualify our design with Bluetooth SIG.
NRF51422 QFN48 nRF51 SDK v10.0.0 SD 310
When I use QDID 62791 to generate a test suite for PTS on the SIG website, the...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
Hello,
I am working with the nRF52 DK, SDK 11 and especially with the ESB protocoll. I started with the provided example esb_low_power_ptx/prx.
In the documentation...
Hi,
I wish to encrypt my application to protect my code. I've tried running my hex file through openssl
openssl enc -aes-128-ofb -nopad -nosalt -e -K XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX...
There are an example which based on Nordic's implementation of BSD Socket API (the client-side).
Also, I have seen the lwIP Socket API in nRF5 IoT SDK, but, there no app...
Hi,
I am new to nrf51-dk and I am using nRF5 SDK v11.0.0 and S130. I wanted to perform the task below.
I have a couple of nRF Beacons and want to program one of it...
