Hi,
currently I'm migrating my application from SDK5 to NCS and I'm facing a problem with the application size for a BLE update. In the previous SDK5 there was the softdevice...
Hello Nordic,
We have recently purchased an nRF52840 Dongle. We were able to sniff the BLE packets over the air. So it is found that all the packets that we are able to...
Hello,
I’m working with the Matter Light Bulb sample in nRF Connect SDK v3.0.0 , and I’ve run into build issues when enabling certain optional commands in standard clusters...
When Enabling an advertising set already enabled on the Softdevice Controller, the HCI error command disallowed is produced when according to the BLE specification 6.0 it...
Dear Forum,
I have an nrf54l15 device and I would like to send a pure sinusoidal tone and measure the phase difference, retrieve I/Q values at the other device. This is...
Hi,
Is it possible to make the MQTT connected device receive the Shadow config updates and AT Commands immediately? Based from our testing, the device only receives the...
Hi! We are having problems pairing a nRF52840 against linux (ubuntu 25.04). Pairing fails instantly, before any passkey is shown on the host, returning with code 9. Short...
Hi,
I want to make sure that the nRF52832 can start working (turn on) with a 1.8V power supply. Therefore I went to check the default value of POFCON register, in which...
Hi,
I got the PWM example code working, but I need only 3 PWM pulses (14usec on time and 34 usec off time). How do I configure the PWM pins to output just 'n' cycles? thanks...
Hello,
I have downloaded the nrf52 sdk (version 0.9.2) and following the steps listed here: infocenter.nordicsemi.com/index.jsp , to run the blinky led example. However,...
hi, i'm looking for layout and schematic (altium ver.) of attatched nrf module (nrf 51822 BLE).
how ans where can i get this ????
actually i need the imformation...
Hi,
For each sdk version there is a release note of known bugs which is good :-)
I guess it lists the bugs known at the time of the release of the sdk.
Are these posts...
Hello,
I am developing in NRF51 with gazelle communication. I specify in project setting (in IRAM) to use full RAM of my nRF51, and use MicroLib. My last working application...
Hi,
I wonder if anyone knows any free C++ compilers for nRF52. I tried the mbed but it is not fully supported for nRF52.
The regular GNU GCC: arm-none-eabi-gcc works perfectly...
We are working on a project using the nrf52832 (SoftDevice s332 v0.9.1alpha, nRF5 SDK 11.0.0) in which we build a library as a hex file and and load it into a known flash...
Hi Guys,
I am using Bluez 5.39 on Ubuntu 14-04 acts a the peripheral by running "example-gatt-server" which creates 3 services and serveral characteristics within it. ...
In a project, I know the Bluetooth address from the machine, also know the phone's address. I want to let Bluetooth devices from the computer and mobile phone side of Bluetooth...
When I use the example of ble_app_uart(SDK : nRF5_SDK_11.0.0_89a8197) to measure data througput ,I find that i cannot get the complete packet of 20 bytes.
The operation is...
ble_ant_app_hrm.rar Hi!!
I want to design dual mode(BLE UART +ANT) but unfortunately I can not built it well.
Can anyone tell me what kind of function or parameter? I based...
Hello,
I am using the nRF51 dongle to try to observe the packets sent between two soft devices. I have inserted the dongle into one of my PC's USB drives and am holding...
I'm running s120 v1.2 & SDK 9
My application will connect to, up to 8, known peripherals. If the connection is dropped or not established, my central app will try to continue...
