I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
Hello,
I've been all over the forum trying to solve my problem but I just couldn't find enough information.
I'm trying to set up notifications in my application, but...
Hello,
We're using SDK v14 and nRF52. To pass some data between reboots we're using the general purpose retention register. However, it seems like it's impossible to call...
I try to transfer the codewords from nrf51822 Dk board to a dongle board, while the dk board is PCA10028 and the dongle board is PCA10031, when I change the port numbers and...
I'm new to the nrf51822, i was connected led to one of the gpio pin of nrf51822 development board. In 1 minite i want to toggle led 20sec and remaining 40 sec in sleep. After...
The SDK 12.1.0 documentation for the FDS library says the following:
FDS_THREADS: If set, the FDS module can be used by multiple modules at the same time (for example...
Hello,
I am trying to measure the current consumption.
i could cut the SB9.
and i use analog discovery and measured!!
the picture is shown in below.
gyazo.com/b9f5607148cd9415ea7d1ee6ac644373...
Hi
I have tried to make use of the FDS for storing data and encountered this behaviour.
The required setup of the sys_evt_dispatch() & fs_sys_event_handler(sys_evt) are...
Hi,
were are looking forward to redesign our PCB. The nRF51822 will communicate via I2C which sinks up to 3 mA and 15 IOs will source the maximum rate of 15mA. Additional...
Hello,
I implemented a function to add characteristics to a service, but I'm having a problem when I add notifiable characteristics. I pass a set of flags to my function...
Hi,
I set a debug LED on as the very first thing I do in main. Randomly (sometimes 2 in a row, sometimes 1 in 100), sometimes my debug LED never comes on and no code is executed...
Hey Everyone,
I am new to nordic development. I am really used to programming with easy environments like the Arduino. I have seen some examples using the printf() command...
Use the Nordic \ nRF5_SDK_12 _f012efa 2.0-3 d \ examples \ peripheral \ pwm_library routines, now can output two lines of PWM, but want to two way different PWM phase have...
Hi there. I'm Matthew!
I noticed that there were contests sponsored by Nordic in the past, such as
Startup Weekend, June 15-17, 2012
The Nordic Semiconductor App...
I can use nRF Toolbox as a central to test various nRF5 as BLE peripheral samples.
Is there any sample app (iOS or Android) to test the few nRF5 as BLE central samples? ...
