Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Hi,
We are planning to build a Mobile application for IoT involving Bluetooth communication. We came across a few part numbers of Nordic for this. We would like to know...
I had purchased the Red Bear Labs "Micro" board to develop code using their MK20 USB Dongle and Arduino.
If I "hack" the programming cable to emulate the "Micro" daughter...
Hi ,
I have recently bought a nRF5232 PCA10040 development kit and i am trying to interface nRf52832 development kit(Master) with AS3955(slave) over twi. I tested the twi_scanner...
Hi all
I'm trying to build a generator based on NRF52832. Outpit signals are: 8MHz clock and two latches signals highly sinchronized with clock - RGB_LAT and TXT_LAT. For...
Hello,
I have a question on how to calculate the capacitance based on oscillator relaxation for NRF52. For example, in the Csense_drv example, when pin is touched by finger...
Hi,
I have a working scanner and manage to require timeslots with the below timings.
Interval 300ms, scan window 50ms, Timeslot length 10ms.
But when i try to...
Hi,
Trying to implement a simple Hardware UART in parrallel with Ble on a custom board with mdbt42 Raytac module. I have the following compilation error:
*** Using Compiler...
I was trying to integrate mesh network into the ble_uart. I am using softdevice v7.3 and sdk6 with nrf51822. I followed the instructions given in the github link text
....
Hi, I bought an Arduino PrimoCore card and I read that you need to buy the Alicepad card. I can not find it on the net. But was it put on the market? Thank you.
Hi,
I have added new UUID (Service and Characteristic) into the uuid_definitions.json but it's not used in the application.
To try I put a error into the json file and...
Initialization:
The softdevice is initialized as in the BLE UART example. The body of the ble_stack_init() function is identical to the BLE UART example.
SPI is initialized...
I have two supplier for provide me nrf52832's based modules.
So I tested it and both is ok. The distance used pcb antenna almost the same (about 80m).
If I use on external...
My application is built using the nRF52832 device.
The system must only be "active" between certain times (5am through to 9pm).
I am a newbie and have no idea how to set...
Hi,
what are the minimal required steps to get the zephyr HCI-UART on a PCA10040 working with Linux BlueZ?
The steps I have so far [My host is Ubuntu 17.04]:
Physically...
