I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hello,
I've recently properly started programming my nrf52832 DK with segger embeded studio playing a little with the debuging tool break points modifing example ect.....
I test ble bond with 'ble_app_gls' in sdk 12.3.0
eg.nRF5_SDK_12.3.0_d7731ad\examples\ble_peripheral\ble_app_gls\pca10028\s130\arm5_no_packs
my phone is meizu mx4, android...
I feel Slave Latency is unnecessary.
For example :
Connect Interval is 100ms,
Supervisor Timeout is 4000ms.
So the Slave Latency must be 39.
if I set Slave Latency...
Hello,
When using extended ATT_MTU without DLE, and the MTU is larger than the LL data length, I know that the MTU is divided into smaller LL packets when sending.
But...
Dear Nordic Devzone,
I want to run an Arduino Ethernet Shield with the Wiznet5100 on the nRF52840. I was wondering if there was an easier way to do this then having to...
I am designing the BLE solution using nrf52832 . The board will be two layer board with solid ground plane in the bottom layer and signal and ground pour in the top layer...
what is a valid publish handle, when I run pb_remote_client, first I input "1" and one pb_remote_server device has been provisioned, and then I input "233", it happens "MESH...
Hello,
I used translation software.
I am measuring current consumption.
I supply it from an external power source.
I connected the SB 12.
After that, I supplied...
Hello,
I'm having trouble to work on the nrf52832 DK with the accelerometer.
First, I tried to wire the accelerometer as I was wiring it on a Arduino Uno but I couldn...
Hi everyone, maybe I'm wrong but I think that the Garmin oregon 600 uses a ANT+/BLE chip made by NordiSemi, it's possible to know exactly which one it is?
Thank you a lot...
Hello,
i'm trying to DFU from 13.1 to 14.1..
What i have tested is flash(SD + B) + dfu(APP) on both versions. Now i'm trying to DFU all from sdk13.1 to 14.1.
Is it...
I know that latest nRF5 SDK and nRF mesh SDK support SES, it's really a good news for developer. I'm just curious that, can I use SES to flash SoftDevice on macOS? If so,...
Hi;
I am using NRF52 DK(pca10040) board nowadays with sdk 14.0. I read a blog post about power consumption in nordic webpage.( link )
In this blog post, there is a webpage...
I´m currently developing ble peripheral application for the nRF52832 with SDK v13.0.0. I need to have a secure connection between the nrf and android or ios mobile device...
