Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Hi Nordic DevZone !
I'm facing an issue that I cannot manage to fix by myself.
So here is the brief: I'm trying to create a BLE beacon that will send some analysis results...
We are working with the nRF7002-DK board and need to measure and minimize power consumption. We are using Wi-Fi in our application and currently working with the sample nrf...
i am working on controlling rgb led with nrf52832 using ble which is based on ble_app_uart example script so my script is working properly on your development board everthing...
Hi,
I want to measure the current draw of the MCU only on the nRF52840DK while I am running my custom code. I want to exclude the current draw of all components except for...
Hi,
I’m currently working with the nRF52833 together with the nRF21540 Front-End Module (FEM). I have configured the FEM to provide a gain of 10 dBm. I have a few questions...
Hi community,
I have a similar custom board as Thingy53, which has the nrf21540 module on board.
my purpose is to turn on the nrf21540 and do the reconnection, when...
Custom PCB with nrf5340/nrf7002. Currently was using NCS2.9.0, with WPA2-PSK connection to the wifi.
While trying to enable use of WPA2-Enterprise, I updated to NCS3.0.0...
I want to use Nordic 52840 DK (Bulb FW) as DUT to setup Matter Certification test.
I have completed below steps:
1. Flash Raspberry Pi （Ubuntu Server 24.04.2 LTS (64-bit...
Hello. Right now, I am connecting an external flash using SPI. The external flash is used for firmware updates. I'm trying to launch sQSPI to access the external flash. I...
Hi,
does the Azure functionality in the nrf connect SDK support the SAS authentication? I need to connect only with the SAS key, and as far as I can see, that's not possible...
We are currently working on a project using the Nordic nRF5340 and nRF7002 DK, which includes 1MB of internal flash and 2MB of external SPI flash. Our application codebase...
Hi Q&A My keyboard chip is NRF52832, and the program uses ESB 2.4G communication. The receiver dongle uses NRF52833. Now there is a problem that when the CAPSLOCK is clicked...
Dear All,
In our company, we have replaced the NRF52811 (ublox module) with NRF54L15 (raytac module) for new batches of products.
The fw is a simple BLE to UART bridge...
I am using 2.9.1 toolchain and sdk with a custom nrf5340 board and trying to use High Voltage (HV) with DC-DC mode. I don't know much about it as I have been using a nrf5340...
