Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
Hello,
I want to use NORDIC nrf52 to perform some power consumption Analysis. Is there any eveloution board from NORDIC that don,t have debugger connected to it? I want...
Hi all,
Is there a tutorial that explain better the bonding information and whitelist? I have more doubt about that.
My first code i have pairing and bonding:
...
hello..
I'm actually working on nrf51822,i could complete the advertising part successfully("hello world")..NOW i want to add privacy feature which allows an advertiser to...
Hi there,
I am working on the SDK13 project template that I am modifying in order to install a vendor type uuid.
But my code crash on "advertising_init" and ble_advertising_init...
While using the secure bootloader image and test application works consistently using the development kit I have not been able to port the solution reliably for our custom...
hai
i am using mbed to program my nrf51822.i want to set the analog pin p6 as analog in in one situation and as a digital out in another situation. but i am unable to do...
Hello.
After executing the code below, the RAM was dropped and the program could not be written.
for(idx = 0; idx < 7; idx++)
{
NRF_POWER->RAM[idx].POWER = (POWER_RAM_POWER_S0POWER_Off...
I'm studing the project of ble_app_gls/PCA10040/SDK11.0/ ,I have got some questions about the RACP indication pending and retransmittion mechnism. In this project(File ble_gls...
enter code here Hi guys I have managed to program an example BLE_Serial program into the nrf51822 but I cannot see anything coming out from the TX and RX ? Please guide me...
I've tried to install nRF Connect v2.0 on both Win 7 and Win 10 systems, both running Avast Anti-virus (up to date). In both cases the antivirus gives a warning about IDP...
I have the Memory Manager module enabled in my custom sdk_config. Within the module, I have both of the following defined.
MEM_MANAGER_ENABLE_LOGS 0
ENABLE_DEBUG_LOG_SUPPORT...
Hello - Is the long range option programmable in BT 5.0? During the run time, is it possible to switch between high speed and long range mode dynamically depending on the...
I am specific about master as I have to connect two simultaneously(obviously to two different pins pair). Plz provide any code outline if you have, Thank you in Advance
Hi.
I would like upload firmware from Atmel microcontroller to nRF51822 with SD130.
I suppose that I have to use single_bank_serial_s130 in nRF51822AA, but what I have to...
