Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
Arms labs published some Bluetooth stack vulnerability
go.armis.com/.../BlueBorne Technical White Paper-1.pdf
Nordic answered that BlueBorce is no effect for LE.
...
Dear Nordic,
nRF52840 is very good solution and we are planning below.
What I want to do:
WLAN Firmware to be stored in nRF52840 Flash
nRF52840 Flash is sufficient...
When I am using power manage function to keep device low power mode, for every 6 milliseconds I am getting small spike of ~300 micro Amp and average current of 300 micro Amp...
Hello Sir,
I’ve been used nRF24L01P controlled by DSP to transmit and receive data for few months. The nRF24L01P is run in 1Mbps mode. The SPI of DSP is set to send 8 bits...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hello,
I have read a lot posts which has the same title unfortunately I am still unable to solve my problem. I am using pca10028, s110, SDK 6. Code is based on BLE_app_uart...
Hello,
on my computer I have the IAR Workbench (8.11) installed.
I want to start Bluetooth software development.
Therefore I installed nRFgo, unzipped the nRF5_SDK_14...
Hello
in sdk14.1 in examples/ble_peripheral/ble_app_buttonless_dfu i get this error when compiling with g++:
make[1]: Entering directory '/home/work/software/nordic/sdk...
Hello,I want to make NRF_LOG_BACKEND_UART work with NUS . The nus work with app_uart_fifo,and the NRF_LOG_BACKEND_UART work with app_uart. I try to make them work together...
I am using NRF51822,S110,16Mhz XOsc. In this if Controller goes to sleep mode the current consumption is 4.9mA. In my application at sleep mode BLE should be connected and...
If I make a product using the nrf24lu1+ chip how can I register a PID for it? The VID is 0x1915 and I know that Bitcraze uses a PID of 0x7777. The Linksys WUSB11 v2.8 802...
Hello
We have nRF51822 chip on our board. We want to make next version of the board. But heard that nRF51822 will be no supported in the near future. So the question is...
Hello,
I am having an issue with my SAADC, it seems to hang while calibrating. The flow of my app is as follows, on my main the SAADC is started with saadc_start() , where...
