I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
We are using a nRF52840 (QIAAAA) on a custom board which replicates exactly the schematic used by the development kit (PCA10056). When using Segger RTT for debugging purposes...
I am using adv_report_parse to try and return the device names the scanner picks up. However device names are being printed repeatedly.
I have 4 to 5 devices around me...
Hi
The serial connection handler "ser_conn_handlers.c" may case an INVALID_LENGTH error when receiving Advertise Reports (or other long BLE events). The reason for this...
I have BLE Nitrogen. It is defined as a disk on which it can be dropped hex and it is loaded. Please explain in detail how to make hex which can be dropped on the device....
I have code running on a nRF52 device, with SoftDevice enabled, based on the example given in this topic:
devzone.nordicsemi.com/.../
This runs fine on its own, and...
Hello !
I am currently working on a custom board on which I don't need 32.768kHz. I want to use P0_1 as an interruption pin connected to a pushbutton. The button is connected...
Hi,
I am using IAR embedded version 7.40 and my board is nRF52840 PCA10056,while i was checking devices list in IAR IDE under NordicSemi i can see only nRF51 series devices...
Hey .My source code was compiled against SDK 8.0 now we need to upgrade the SDK to 10.0.
I have just copied the SDK10.0.0"components" folder to my project ( replaced the...
main.c
y_timer.c
y_timer.h
Hi,
I wanted to make the function that get timestamp like mills().
I made this code bellow.
It does'nt move well.
Main loop is unintentionally...
Hi,
During testing I noticed rare BLE connection loses with Softdevice S110 when timeslot session is active. It is hard to catch them with sniffer due to rare behaviour....
I am trying to get the example examples/ble_peripheral/ble_app_template to work from nRF5_SDK_13.1.0.
nRF52832, s132, pca10040
Much of the code works, but inside peer_manager_init...
The device use SDK9.0,during the using of device,when disconnect the bluetooth of phone system sometimes,the system halted.
So I make an experiment about the probability...
Hello,
I am trying the Thread Cloud COAP Client
<InstallFolder>\examples\thread\experimental\cloud_coap_client
on a NRF52840 PDK. I'm using Thread SDK v0.10...
I have troubles with connection using nrf51822 and android phones:
First I connect and bond the device to the phone and it works ok.
Then I periodically...
