Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
In the Bluetooth Light Controller example for the client, in provisioner.c this beautiful comment can be found:
/* Provisioning encryption key storage (this is not how...
Hi all,
Here is my first question on this forum after many hours working with the NRF but for the first time I didn't found the answer :)
My problem is :
I would like...
Hi,
We have custom board with STM32F407 as an application chip and BL652-SC-01 as a connectivity chip. When we worked on SDK 13 and softdevice 4.0.2 or 4.0.4 we had problem...
Hi, I have problem with using printf() in SEGGER RTT.
I've read tutorial and others about SEGGER RTT printf() problem, but they didn't work.
When I use printf() in RTT...
hi,
I found ble_app_multilink_central example under SDK but this is for LED button application.
Is it possible to configure the same example for NUS?
I worrying about...
I have app (based on buttonless_dfu) works on sdk 13, sd 3, nrf52832.
Now I try to migrate this app to newest SDK14, sd 5.
I can't resolve one issue. I have main.c and 7...
hi, I found ble_app_multilink_central example under SDK ,and make it work with NUS. Some problems bothered me.
When the amount of data reaches a certain amount, the transfer...
Hi,
Tried this getting started tutorial:
github.com/.../Nordic_SDK_User_Guide.md
When building project at the end, I get: (After trying max optimization)
linking...
Hi,
I am trying to program a custom board with ISP1507 chip from dynastream based on nRF52832 using the nRF52 DK. I have connected P20 on the DK to the chip as follows...
Hello, myCode: https://goo.gl/ggTei4 & Photo : https://goo.gl/Sq28tC
Please Help me with Dynamic NRF24L01 Mesh network
I have connected nodes via DHCP 01, 02 upto 05 to...
Hello everyone!
Do have any different between Read/Write internal flash with softdevice and non softdevice!
And how can I get example Read/Write internal flash with softdevice...
using the sample code at
invent.module143.com/.../
i am able to use nrf24l01 to communicate raspberry pi with arduino, but the problem is the timing. I found it takes...
Did anyone attempt time of flight measurements with the nrf52 yet? I'm looking into this as a possibility to measure distances. I was thinking that using the 64 MHz clock...
I AM GENERATING A PWM EXTERNALLY (OUTPUT FROM A WATER SENSOR) AND FEED IT TO A NRF51422 BOARD. I WANT TO COUNT THE PULSE COUNT(LOW TO HIGH TRANSITIONS ONLY). CAN I DO IT WITH...
How to configure an app_timer in counter mode. i just want to count number of pulses in pwm using app_timer. i didnt find any example in which app_timer used in counter m...
