Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
Hi,
I measured the current consumption of nRF52DK with the original code of "nRF5_SDK_13.0.0_04a0bfd\examples\ble_peripheral\ble_app_beacon ",
based on the current measurement...
Hi everyone,
I was wondering if anyone benchmarked the time for reading a word from flash on the nRF52840. I was able to find the write/erase time on the specs document...
Hi,
We use the nrf app (Android smartphone) to establish BLE communication with trackers designed with nrf51822.
When trying to connect, sometimes it works, sometimes...
Hello， for the past I've been trying to migrate unsuccessfully my code from nrf51 to nrf52840 S140. Now that I'm unsuccessful, I'm trying to eliminate the possibility of a...
Using FreeRTOS to run nrf_cli. When Serial is not connected (as in RX,TX,GND) the board goes into a reset loop.
There are a few things that seem to help:
Don't run...
hi,
i have tried to write data into flash memory, but i can not, i can read the data from memory.
i had followed your instruction as this link
infocenter.nordicsemi...
In my project, an android phone is needed to connect to two ble devices. All my ble devices are nrf51822. The android phone can connect to and receive data from every device...
Hi,
to investigate a timing problem in my Bluetooth stack, I've hard wired the Radio ADDRESS and END events to a GPIO pin using the PPI. The ADDRESS event is used to toggle...
Hi,
I'm developing a FW with a lot of services and characteristics. Since I added the ANCS service, I have the "NRF_ERROR_NO_MEM".
Configuration : NRF51822_XXAC / S130...
hello everyone,
i use nrf51822-QFAA(256kb flash,16kb ram).i want to use sdk12.3.
at first i can't build the project,after i install some tools, i can build it ok.
...
i am using nRF5_SDK_13.0.0-1.alpha_055eef3 s132_nrf52_5.0.0-1.alpha_softdevice and used examples\dfu\bootloader_secure\pca10040\ for secure DFu OTA .everytime i try i get...
What's the current consumption for a Timer on the nRF52832 when it's used in Counter mode? Do Timers require the 16MHz or 1MHz clock when configured for counter mode?
Hi Vidar,
I am planning to start devlopment on the nRF52 and I would like to use GCC ARM with Eclipse. After having read your post "Development with GCC and Eclipse" and...
