The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hi,
I'm trying to get SPI working with an accelerometer (LIS3DH). I'm currently trying to use the nrf_drv_spi_transfer() function. See code snippets below.
// Initialize...
SDK14.0.0
nRF52832
s132
I would like to DFU the contents of the App Data section. In particular, I would like to erase the contents for a "factory reset" command.
...
I am setting up the DFU example to compile in Clion using ARMGCC 4.9 2015q3 and cmake. Everything compiled as it should and the DFU advertises. However, when trying to do...
hello there,
i want to send and receive data using spi and i2c protocol and i am using nrf51422 .how to interface which pins should i use to make spi and i2c communication...
I have an application that toggles an LED on P0.26 based on a timer and that's working fine. Now I need to add a few more timers so I decided to use the APP_TIMER library...
I am having trouble with an application where the NRF52832 operates several devices as a TWI master. What is even stranger is that I have been working on this code for a while...
I am developing a keyboard using the nRF52832 and example code(ble_app_hids_keyboard).
SDK is SDK14.
Korean/English change is not possible.
The specification I refer...
hello there i have basic question about BLE. what is difference between link layer and GAP??
i know about host and controller. but in both layer there is advertisement and...
We are using the NRF52840 as a basis for BLE-based secure IoT network. I know that the Crypto library enables hardware-accelerated encryption/decryption. However, as far as...
Hi guys, I'm trying to nail down this TWI issue. PAN 89 is related to TWI being used in conjunction with the GPIOTE module. However I manually wrote my own application level...
Related to SDK 12.3.
Quoting this question :
GPIOTE PORT event generated on the
rising edge of DETECT signal. Please
have a look at section 15.1.2
2)DETECT...
Hello,
I am experimenting with sending large notifications from an nRF52 configured as BLE peripheral with SoftDevice S132 v5.0.0. I having some trouble receiving the notifications...
Hello guys,
I would like to execute code once a scan request from any other BLE device is received by the NRF52 using Zephyr.
Unfortunately, I am not able to receive...
Hi everybody,
I have an issue with my application, I want to use the ble with the same antenna that it use in the development board PCA10036,
Could you please tell me...
