I have used the Programmer previously with success. I am attempting to program the Dongle (10059) with a slightly modified version of ble_nusc_usb_dongle. Although it claims...
H ello Nordic team,
I'v found a bug on mqtt sample (using both ncs 3.0.0 and 2.6.1).
Description
Settings CONFIG_MQTT_SAMPLE_TRANSPORT_CLIENT_ID and trying to connect...
Hello Team,
I have flashed the bap_unicast_server bluetooth sample on my nRF5340 Audio DK. No build or flash errors. When I connect to my phone it connects properly. I'm...
I'm working on a project involving a USB dongle based on the nRF52840 SDK-2.9.1, which needs to communicate with a sensor (also an nRF52840) and transmit data via USB to PC...
Hello Nordic team, For the ( POC), I configured ADC channel 1 and interfaced a potentiometer to pin P1.14. The ADC was set up accordingly to read raw value from the potentiometer...
Hello, I have been going through the DFU and FOTA lesson in the Nordic intermediate course. I see that there is a FOTA support for a scenario in which we want to update a...
This sounds like a stupid question... but I would like to clarify if this pin is an input or output. I think it's power in but want to make 100% sure as I'm spinning a PCB...
Hi,
We bought a mac bd addr pool from IEEE
Where is the best way to store this mac adress during production ?
We guess the type will be: BLE_GAP_ADDR_TYPE_PUBLIC
Do...
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi. I'm using nRF51822, SDK12.2.0, S130.
I finally compiled bootloader_secure which was very hard.
Q1. After run bootloader, I can find the device using DFU "DfuTarg"...
Hi ,
I am trying to use the new softdevice SD130 V2.0.0 and have not had any luck when using the most recent version of SD130. I ran the same application with SD130 V1...
I've nrf51dk development board. It has nrf51422QFACA10 chip and has 32kB ram and 256kB flash. I downloaded sdk V11 and programmed ble_app_beacon_s130_pca10028. It worked fine...
I try to move my project from Keil to GCC but I get some different behavior. To show the difference I use examples/ble_peripheral/ble_app_uart
The part of the code below...
I have purchased a nRF52 DK and want to use it by emulating an ANT+ Stride Based Speed and Distance (foot pod) and pair that with my Garmin FR235 running watch in order to...
Environment:
Segger Embedded Studio
nRf51 Developementkit using jLink OB firmware
S130
We're using the \nRF5_SDK_12.2.0_f012efa\examples\ble_peripheral\ble_app_template...
I'm trying to enable interrupt for radio events.
I have this code in main:
bsp_board_leds_init();
(...)
NRF_RADIO->INTENSET = 1 << RADIO_INTENSET_READY_Pos;
NRF_RADIO...
Hi!
I would like to create a RTC for stamping log messages, with 1ms resolution and including time from year to millisecond, like: YYYY-MM-DD HH:MM:SS.mmm.
What would...
Hi ,I'm trying to program Qtouch with nrf51822, and i have a question : is there any libraries i can use for my Qtouch in nrf51822 ?
i'm using QTouch :Atmel- AT42QT1070
...
I am using Nordic SDK to develop an application. I need to turn PWM off and turn it back on (to produce a beeping sound from a buzzer). To do this I went into the bsp.c file...
Hi..
I am using NRF51822 , we are using Ceramic antenna. We are thinking of designing body similar to the image. perimeter of the body is made of metal (aluminum) of thickness...
Hello
I am looking to make a program on nrf52 in which i send various values from nrf UART app on a mobile, and each value controls a LED on a GPIO. For example, sending...
Hello,
I want to combine the RTC example from the peripheral to one of the BLE peripheral examples but the problem is that the BLE peripheral examples need the softdevice...
