Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
I found out answers for calculating data rate during connections, which depends upon connection interval, no of packets allowed in each connection and no of bytes in a single...
I am trying to stop RTC by pressing one button and wake up again by releasing the same button.
My RTC now runs around 4 uA while being on system-on sleep mode by __SEV();...
Hi,
I managed to get dfu working in application (with hrs). But on the last attempt to erase page with bootloader settings there is no event generated from softdevice and...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
I would like to know how frequently my peripheral is sending advertising and data packets. I've tried using ble-sniffer-osx but it doesn't actually reveal any device names...
Has anyone successfully used the Android-Beacon Library to detect the nRF51822 Beacon on and Android application? I tried several different layouts but I just can't detect...
Hi everyone;
i think about possibility of using nrf sniffer with custom nrf51822 (QFAA) board . if yes, how can i achieve? could you please help me about it
Best Re...
Hi All,
This is my first time i am designing a PCB for nrf52840, I need a suggestion regarding the antenna to be used. I am going to have an application over BLE. Which...
I want to add a timeout to the secure DFU bootloader if I enter it from the application. I found this post here devzone.nordicsemi.com/.../ but unfortuately I can't use the...
Hi I'm looking forward to hear if I could program an nRf51822 QFAA without using the development kit/board. The chip I have currently is a N51822- S4AT, from Wireless Tag...
we are facing problem with smt M905 module. is there any basic error with this module pad?
smt factory in china failed several times to solder this module.
Hi - In my app, I'm using Bluetooth, the ADC, the TWI, and the SPI. The general idea is to measure lots of things, store the data in SPI NOR FLASH, and occasionally flush...
I'm testing a custom application with the following configuration:
Custom app based on the ble_app_pwr_profiling SDK example.
Using SDK 13.1
S140 SoftDevice s140_nrf52840_5...
Considering that as soon as the connection is established (GAP Peripheral device receives CONNECT_REQ packet) and advertising is over.
Is it possible once the connection...
