nRF52840 NCS 3.0.1 RCP
I just installed the NCS 3.0.1 SDK. I am trying to set up a border router on a Raspberry Pi 4.
I followed these instructions on the Raspberry Pi...
Hello,
I have a legacy project that is using nrf5 sdk v17.0.2. I need to add the BLE DFU functionality to this project based on the nRF52840. Are there any examples on...
We are trying to evaluate nrf9151 for working with Soft-SIM. Are there any instructions for configuring the Soft-SIM through AT command mode, or do I need to use another mode...
I was doing some developement for a custom board on NCS v2.9.1 when i noticed some of the changes i was making in my prj.conf weren't being set in the application. My impression...
In my circuit I have a MOSFET which disconnects the battery. There is a GPIO pin which turns this device on and I'm using regulator-fixed to drive it during start-up. A short...
We are currently using ncs 2.9.0 on an nRF5340. We use the BT_HCI_OP_VS_READ_VERSION_INFO to determine at runtime what version of the BLE stack is present. This information...
Hi I'm trying to load a custom board with nrf9160 with the Serial LTE Modem, and route the AT commands to the UART from a coprocessor (ESP32C3) I have followed the guide on...
Hello,
I am using nRF5_SDK_12.0.0 with soft device s130_nrf51_2.0.1_softdevice. I am trying to implement the DFU service in my application, for which I am following:
...
Hello :) I'm trying to run the DFU example (dfu_dual_bank_ble_s132_pca10040) for the nrf52832 chip on a custom board. The Bootloader crashes/resets at the SOFTDEVICE_HANDLER_INIT...
spi.rar
Hi,
As a beginner, I want to combine spi and uart example in nrf52 11.0.0 sdk, for my application. I have included all libraries and driver files from uart in...
Hi,
I would like to ask your support for a very unusual problem that I'm facing with a project based on nrf51822.
The board under test is based on nrf51822, SDK12.1...
Hi all,
I'm trying to set up DFU over BLE - Single Bank using:
Mac OS 10.10.1
gcc 4.9 SDK 7.1 w SD110 7.1.0
PCA10001 v2.2.0
MCP 3.7.1.8567 (modified lib/dfu folder...
I've read a lot of questions regarding the AES decryption using the nrf51 where it was not possible. Is it now possible with the nrf52 or the even newer version?
Thanks,...
this is capture image.
what does that happen?
The debugger is I-Jet and debugging via SWD.
The connection did below. and I'll assume the red line is number one. I...
Hi
I was playing around with the new serialization code in the SDK 13.0.0 and the PCA10056. I was able to compile the connectivity code, but when I try to configure the...
hi, all
I want to run nrf's example named "proprietary_rf->esb_prx", the deafult setting of keil memory is
IROM1: 0X0 0X80000
IRAM1: 0X20000000 0X10000
It can compile...
Hi,
We want to make PCB of NRF52 and we want to buy PCB design software.
Can you guide me that how many layers of PCB is required and how many pins will be required...
I've searched for enabling notification, but there are some points that I can't understand.
GATT characteristic attributes and characteristic cccd values are dedicated...
Hello,
When I check RESETREAS, I have some reboot reasons rised from software error (SREQ).
I know that these errors are not catched in the app_error_handler because...
I am using ARM-GCC (version 6.2 2016q4) toolchain and make command to compile example code.
I have updated my compiler installation path in Makefile.Windows as well.
...
