Hi
I'm migrating applications I wrote using SDK 17 to nrfConnect 3.0 with Zephyr.
I implemented USB devices with combined multiple USB classes. One of those classes was...
Hi,
I am working on ncs 2.9.1 @ nRF54L15.
I followed this academy course to add a single channel saadc in simple mode:
ADC read works properly, but the current read...
Hi,
In one of our future hardware designs, we have a MPU (running LInux) connected to a Bluetooth SOC over a serial interface (uart/spi/...).
Our first approach was...
Hello everyone,
I'm working on an NRF54L15 DK evaluation board and I need to use NFCT pins as normal GPIOs. I found out here that I should define CONFIG_NFCT_PINS_AS_GPIOS...
We are certifying our device at KIWA. they are testing the WLAN adaptivity and the test is failing. Here is the failure description:
" It was a struggle to perform the...
I downloaded the ncs2.6.0 version using Baidu Cloud in the China region, then set the path in Toolchain Manager of NRF Desktop, and Toolchain Manager correctly identified...
Hello! The PCN 219 rev 1.1 says "The new device revision of nRF54L15-CAAA is not drop-in compatible with the current revision, requiring update to PCB schematic
and layout...
Currently I am searching for s130 example code. I know it's in alpha stage, but I think it should be possible to start to experiment with it, isn't it?
In the past I've...
Hi,
I tried following code to close the ANT+ channel on channel not connected to the other ANT+ device:
#define CBSC_TX_ANT_CHANNEL 0
void ant_adv_timeout_handler(void...
We have a DFU which uses a different set of of services than the main app.
Both of them share bonding information which is create by our main app.
Once we switch to DFU...
I am trying to build a system with a single PRX and up to 5 PTX devices.
Initial development work was done with a single PTX with it's address on Pipe0 in the PRX. I have...
I have a CC2540 and CC2541 chip with me. I did figure out that both of them are working, but now I am stuck up at how to practically test if the proximity profile is working...
Hi,all
I want to simulate HFP(Hands-Free Profile) on S110, and i know HFP is one profile of Classic Bluetooth.
If i implement HFP on nrf51822, it can work will?
How would you go about extending Gazelle ?
For example I have a host with four devices. I want to connect this host to another host with its own set of devices.
Hi,
I'm planning to use a nRF8002 to transmit via BT the state of a pushbutton to a RFduino. I've my RFduino ready to receive data (and this works when paired to my iPhone...
Hi,
I'm trying to detect the nrf8001 by my Mac. My android device detects it, but when I search for it in mac, it's not detected.
I'm using this library: github.com...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I recently started working with the NRF51822 and PCA1001
I need to read data from MPU9150 accelerometer via I2C and transmit the results over BLE.
I connected the...
Hi,
I'm communicating ANT through softdevice ant event handler as follows:
err_code = softdevice_ant_evt_handler_set(on_ant_evt);
void on_ant_evt(ant_evt_t * p_ant_evt...
Hi,
I'm using PCA10003 board with nrf51422 chip with version E0 and tried connecting ANT with ANTware II software using the HRM example and it works fine on UART but on ANTware...
Hi,
I'm using BLE and ANT+ concurrently with nrf51422 and s310 softdevice. I'm using on_ble_evt for BLE and on_ant_evt for ANT+.
I'm using following code for advertising...
Hi,
I want to add a bit (about 100KB) off data to my project in Keil.
I need to work out where to locate it (to avoid my code and the S120)
I can't seem to find a memory...
