Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
I'm using SDK 12.2. The FDS operates on word-sized data. How can I ensure that my data structures are word aligned and multiples of the word size? E.g. if I'm trying to write...
Hi everyone,
I am looking for reports and/or certifications that can help with our own device's certification process.
Would you know where we could find such reports...
Can I configure security parameters my own way?
I read some BLE profile but there are not explain about security configuration.
And I tested by using PCA10028, iPhone4s...
I am trying to setup an interrupt to fire whenever any of 6 GPIO pins change value using an nRF51822 with soft device. I found the example that uses GPIOTE to get an interrupt...
Hi. I'm using nRF51822AC, SDK12.2.0. S130 v2.0.1.
I just want to make DFU program. But I think it's a little bit confusing. So I want some explain.
Q1. What is the difference...
I'm wondering whether I'm missing something.
This is the callback called from finish_transfer in both nrf_drv_spi.c and nrf_drv_twi.c.
This parameter is useful because...
Hi,
I am working on the examples\ble_peripheral\ble_app_uart sdk 12 example on SES.
I was first setting:
FLASH_START=0x1B000
SRAM_START=0x20001EB0
Then tried...
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
Hi,
My code always throws "NRF_ERROR_INVALID_STATE" error and reset in nrf_drv_gpiote_in_init.
I tried many pins all of them are free and not used:
#define BUTTONS_NUMBER...
Hello,
is there a way to check for NRF_ERROR_BUSY before issuing a new command?
The idea would be to create a timer to retry issuing a/the command if the NRF is not...
Hi,
After following all instructions on: gnuarmeclipse.github.io/.../
And after installing all Nordic Semi dependencies on eclipse.
I import on eclipse the UART_Loopback...
Hello team,
I got a DEV KIT NRF52
And I'd like to get all my LOG : NRF_LOG_* ( NRF_LOG_INFO… ) From my USB interface Serial:
/dev/tty.usbmodem1421
I made sure...
i read devzone.nordicsemi.com/.../ that simple multiple saadc-s is not so easy.
I also looked at github.com/.../ble_app_uart__saadc_timer_driven__scan_mode to use multiple...
