Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
Hi,
My first objectif is that the Micro:Bit consumes less than 2μA without the BLE. I read that the Micro:Bit program was not powered if the Micro:Bit is powered by the...
Hi everyone,
I am writing a program in Keil whereby I have to send a large amount of data through BLE notification in real time. The program works by having two timers...
I want nRF52832 to be a central device which will take an input from nRF51822 (peripheral device). Also, Is it possible to make two nRF51822 talk to each other?
Hi,
I having an nrf52832 board and using gnu arm, nrfjprog to program the device. i reading data from two different sensors using spi and TWI in two different codes. now...
Hello all,
I have received "nrf51822 smart beacon kit" connected the battery power and i can detect the device in nrf Beacon app. but the issue is when i select the actions...
I am going to have streaming data come through a characteristic on an S110 device. When the client writes to the characteristic, my peripheral device will read the characteristic...
How do I use Wireshark to see the connection interval negotiated between my nRF51822 peripheral and a central which is a mobile app? Which messages should I be looking for...
Hi all,
I am not very proficient in NORDIC and BLE. I was wondering if you could answer me.
I am developing a module using NRF52. I have a redundant wireless communication...
I am using a PCA10040 with a nRF52832 mounted on it. I am trying to match the IC revision with the packet variant as explained here .
The problem here is that the chip...
Hi I am new to Nordic development and set up all the tools required for compiling and flashing program to nrf52840 0n ubuntu. I downloaded nrfjprog and jlink segger and put...
Hello,
I'm trying to use a nrf51 dongle (PCA10031) as a BLE sniffer. I'm following the ble-sniffer_win_1.2_User Guide.pdf.
On the required software, i need to install...
Hi,
I try to use the example ble_peripheral -> blr_freertos -> ble_app_hrs_freertos and I add to the thread a fds_register() and fds_init(). Problem: In the call back function...
Hello, I am using the NFR52 DK (s132) in peripheral mode. I have implemented a pairing mode based on a static passkey. However, the available time to enter the key in the...
Hi,
is it possible to atomically change both the GAP address and the advertising message in one step? I want to broadcast two different advertising messages with each of...
