Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Hello,
I am trying to compile the example ble_app_eddystone with the SDK12.2 for the nRF52_pca10040_s132
While compiling with SEGGER I get the error
Compiling...
Hello,
I set up a project on the base of "BLE_APP_UART" to which I added header files and configured the sdk_config.h
Now I get these warnings during compilaiton:
...
Hi!
So I went from the Battery Service example to create my own service which went well and everything. Now I don't need a battery service, which is why I was trying to...
Hello,
i am working on Low current consumption project.
i have one question. what will be the good option to use the SPI or TWI ?
who have less current consumption ?
...
Hi, I want to ask some questions about BQ24090.
According to the schematic in the datasheet of BQ24090 , I have several questions below:
When should the led indicator...
I added the peer manager in my SDK11.0.0 application. I also have OTA DFU but everytime I boot into the bootlader, the first connection fails and I have to reconnect again...
Hi,
I am getting the "Couldn't connect Nordic_HRM" toast using the experimental project.
I saw the question but the answer there (sample code for selfie stick) is a very...
If I enable the Data Packet Length Extension and I enable the Connection Event Length Extension, having a connection interval of ~400ms I know that I can reach up to 251 bytes...
Hello,
I am trying to implement a Heart Rate Monitor Interface (HRMI) board with my nRF52, using the TWI_sensor example from SDK 12.2. I am unable to read any heart rate...
I use the S130 stack and enable the service changed feature when enable the soft device. I found the handle can be got when call add API. But this is GATT handle. How can...
UPDATE:02/28/2017
I MAKE A BOARD ,WANT TO KNOW DOES THIS PIC MAKE SENSE?
I WANT USE STM32F072B REPLACE JLINK OB.
STM32 HAS USB I WILL WRITE CODE MAKE A virtual...
Hi,
I download nRF5_SDK_11.0.0_89a8197 and open the SPI example in the peripheral folder using Keil V5.20, but I found that the project cann't be build. Could you tell...
I know the Source code for the MCP is not provided ..
I also Know the the masteremulator dll is available ... and there are several samples code demos available.
but I am...
hello,
In nRF 52, after executing ble_advertising_start after BLE_GAP_EVT_DISCONNECTED, although BLE_GAP_EVT_CONNECTED is set on the device side although the central is disconnected...