I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I'm using SDK 12.2. The FDS operates on word-sized data. How can I ensure that my data structures are word aligned and multiples of the word size? E.g. if I'm trying to write...
Hi everyone,
I am looking for reports and/or certifications that can help with our own device's certification process.
Would you know where we could find such reports...
Can I configure security parameters my own way?
I read some BLE profile but there are not explain about security configuration.
And I tested by using PCA10028, iPhone4s...
I am trying to setup an interrupt to fire whenever any of 6 GPIO pins change value using an nRF51822 with soft device. I found the example that uses GPIOTE to get an interrupt...
Hi. I'm using nRF51822AC, SDK12.2.0. S130 v2.0.1.
I just want to make DFU program. But I think it's a little bit confusing. So I want some explain.
Q1. What is the difference...
I'm wondering whether I'm missing something.
This is the callback called from finish_transfer in both nrf_drv_spi.c and nrf_drv_twi.c.
This parameter is useful because...
Hi,
I am working on the examples\ble_peripheral\ble_app_uart sdk 12 example on SES.
I was first setting:
FLASH_START=0x1B000
SRAM_START=0x20001EB0
Then tried...
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
Hi,
My code always throws "NRF_ERROR_INVALID_STATE" error and reset in nrf_drv_gpiote_in_init.
I tried many pins all of them are free and not used:
#define BUTTONS_NUMBER...
Hello,
is there a way to check for NRF_ERROR_BUSY before issuing a new command?
The idea would be to create a timer to retry issuing a/the command if the NRF is not...
Hi,
After following all instructions on: gnuarmeclipse.github.io/.../
And after installing all Nordic Semi dependencies on eclipse.
I import on eclipse the UART_Loopback...
Hello team,
I got a DEV KIT NRF52
And I'd like to get all my LOG : NRF_LOG_* ( NRF_LOG_INFO… ) From my USB interface Serial:
/dev/tty.usbmodem1421
I made sure...
i read devzone.nordicsemi.com/.../ that simple multiple saadc-s is not so easy.
I also looked at github.com/.../ble_app_uart__saadc_timer_driven__scan_mode to use multiple...
