Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
How is it used? And why to use it?
static nrf_saadc_value_t m_buffer_pool[2][SAMPLES_IN_BUFFER];
instead of
static nrf_saadc_value_t m_buffer[SAMPLES_IN_BUFFER];
Hi team,
we are doing project called indoor navigation using beacons.To get the good RSSI signal strength,in which position should i need to place the beacon. Can any one...
Hello,
I tried to flash an application to the nRF52832. First I flashed the softdevice, after that I flashed the bootloader and next the application.
The application...
We were doing various tests using PCA10040.
Then suddenly I can not connect to the PCA10040 board.
In the boot loader mode of PCA10040 board, connection is made.
What is...
Hi, I use the nRF52832 board (PCA10040 v1.1).
Before creating a custom PCB that uses nRF52832-QFAA, I chose
Q22FA12800025 FA-128 32 MHZ 8.0PF (load cap = 8pF)
and ...
This should not be a sudden my PCA10040.
Jlink are probably going to have failed.
It does not appear in the USB Jlink to appear as Atmel.
Is there a way to recover...
I am doing a project about nrf51822 smart beacon kit and a person has give me this link: infocenter.nordicsemi.com/index.jsp
to download the firmware and hardware files...
Hello,
I develop a BLE central device based on nRF52 (with the newest connectivity firmware and SoftDevice with API v3) and the pc-ble-driver in version 2.0.
Since my...
Hello Everyone,
I am working on nRF51 I need to save data with timestamp (current date and time).
Is there any example code is available so I can set current time and...
Hello,
Recently read about FIDO’s U2F authentication protocol for NFC and Bluetooth smart.
https://fidoalliance.org/fido-alliance-equips-u2f-for-mobile-and-wireless-applications...
hello everyone,
I am doing a project about Ibeacons. I need to make a selfmade bluetooth smart beacon (excuse me for bad English). I found a schematic circuit design of...
Hi all,
I am trying to get an Android Nexus 5X app to work with an NRF chip, and facing some problems, specifically with writing to a characteristic. Really hope to get...
Hi,
I discovered unusual behaviour in a SPI read transfer.
My transfer consists of writing one byte (peripheral register address) and receiving one byte (contents of...
SoftDevice Version s132 SDK Version
12.2 Kit NRF52832 PC10040 DK
I am trying to run the ble_app_beacon example after importing the project into Segger Embedded Studio...
