Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
Hello friends. How to write a number to and read from internal flash. My information about the microcontroller is very weak. I use STM32F103RET6 .
I test The following program...
Hello,
I am able to compile blinky with my SW tool set up, however, when I try to compile a more complex example (ant_broadcast_rx_pca10040_s212) I get issues with the...
Hi,
I hope is not a double post. I am doing a throughput evaluation with my custom board and an app that is based on the Nordic's Android UART app through NUS service and...
I am trying to get the ble_app_uart project to build in Eclipse for the PCA10036 nRF52 board. I have followed the Tutorial titled " Development with GCC and Eclipse" and successfully...
Hello,
i am stuck with this, trying to write to flash using pstorage module. Below is my code.
static void pstore_cb_handler(pstorage_handle_t * handle,
uint8_t op_code...
Hello,
I have downloaded the Hardware Files of nrf51822 smart beacon kit. But I Cant open the Altrium Designer Files (pcbdoc. files). Do u know how to open it or a program...
Hi,
I do test my project one central connect to 4 peripheral(HR and CSC).
and I put the memset(&m_ble_db_discovery,0,sizeof(m_ble_db_discovery)); err_code = ble_db_discovery_start...
Hi,
I use nRF52832 and SDK12.2
The Project is ble_central_and_peripheral and the link define is like below
#define CENTRAL_LINK_COUNT 4
Here will connect 1 HR device...
Hello,
Is it a good practice to modify SDK files?
I mean, do you use SDK as integral part of your project and feel free to modify it, or do you try to avoid it and just...
Hello,
We have connected Nordic+ MPU 9250 and able to read sensor values through UART display, but we wanted to do some excercises and read values, but it's not possible...
hello guys,
i am new in nrf micro-controller. I want to get data from my smartphone and want to write in memory of nrf51822 through BLE. when written process in memory is...
I'm a newby. I'm troubles understanding how to send command to ble. my band have own protocol like this :
if you send 'AB02FF7180' to ble means your band will shock 5 times...
We have a application that use the ADC of nRF51822 to detect a variable resistance (schematic is attached). The current passing through the variable resistor should be around...
Greetings
I am working on an application that logs data to SPI flash device. I am having an issue where it appears that the pin configured as a MISO for SPIM is garbling...
Hi,
I have a running board with NUS service (serial profile). This boards starts advertising until a remote device (android nrf UART app) connects to it. then it starts...
