FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
Hi,
I have Wireshark version 1.10.14 and sniffer version 1.0.1. I send the data out from PCA10040 with connection interval of 7.5 ms and packet throughput of 200Hz using...
The pulldown on the SAADC is 160k. Is it ok to create a resistor ladder by adding an external resistor of, say, 400k, enable the internal pulldown and then input a higher...
Hi NordicSemiconductor's community,
I have a basic question about connection to a BLE peripheral.
I use the SDK_10.0.0 and s110_v8.0.0.
I want to know how to implement...
how to change RX and TX operations ?
i wrote next code:
#include "nrf_esb.h"
#include <stdbool.h>
#include <stdint.h>
#include "sdk_common.h"
#include "nrf.h"
#include...
Hello
I used one example from the nrf52 SDK and wanted to add another functionality to the code. How do I know what to add to that file?
Is there a global sdk_config.h containing...
I am migrating from SDK 12.2 to SDK 13 on Nrf52.
I use Eclipse.
I have a few questions:
In SDK12.2, there was :
Patch for SDK 12 - implements required workaround...
i am using nrf52832 dk. i am trying to change the flash address from 0x000 to 0x0002000. But i can only flash it to 0x0002000 if softdevice is already present on controller...
Hello,
I want to clarify one thing related to the limitaion in SoftDevice S130 V.1 of L2CAP_MTU size by 23 bytes. Is any way to extended it?
Because I see that changes...
Hi All,
We are trying to flash our custom NRF52832 board using NRF52-DK+nrf studio. With the same setup that's suggested by devzone.nordicsemi.com/.../
However, from...
Hi,
Recently i have moved to a much newer version of the SDK and have replaced my uart driver with the new ones, from SDK 12.7. The uart is between two nRF51422s one with...
I did not use softdevice;
//this my code
void SysClk_LFInit(void)
{
NRF_CLOCK->LFCLKSRC = (CLOCK_LFCLKSRC_SRC_RC << CLOCK_LFCLKSRC_SRC_Pos);
NRF_CLOCK->EVENTS_LFCLKSTARTED...
Hi, i just got the tutorial "Getting started with nRF5 DK" with a NRF52DK to run with IAR Embedded Workbench. Unfortunatly i'm not able to set a single breakpoint in the debug...
