I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
I am spending the last 3 days trying to make sure somebody on this plant made it using a mac .
Write a simple program and flash it to the DK. (before we make our own pcb...
Hi,
I'm using nrf51dk board and nrf_log came out correctly on my RTT terminal with built in module. After that I use debug port (P20) to program to my custom module. I've...
Hi,
I have changed in my services so I have added 0x2A05 (service changed) characteristic in my 0x1801 service. But I am not able to read the service.
In didDiscoverServices...
Hi, i'm currently using two NRF52 (1 central and 1 peripheral) using the ble_app_blinky and the ble_app_multilink_central.
I would now like to connect my Android phone...
HI:
I'am an engineer of BLE. And II want PC&Mobile connect my BLE equipment(51822) by type in password like wifi or most of bluetooth Headset.
what should I do. which paragraph...
Hello,
Is there a mechanical specification document for the nRF52 development kit (PCA10040)?
I can extrapolate from the Arduino Uno Rev 3 specification (P1-4 connectors...
hi dear Engineers,
I am affraid to use FLASH to manage PEER data, it is wrong way because of Wr op. limitaion.
Instead of that, EEPROM or FRAM must be used anyway.
How...
Does single bank bootloader in SDK7.1 support ZIP-file ?
I get error REMOTE DFU INVALID CRC ERROR in the end of flashing by nRF Toolbox when I use ZIP.
If I use hex-file...
Hello,
I am trying to implement OTA firmware update using Secure DFU.
SDK - 12.2
Softdevice - s132
Board - PCA10040 (nRF52)
I followed instructions mentioned...
Hello,
I just want to clarity the sd_ecb_block_encrypt() operation cases (S110).
In pp. 23.1.3 of RM (Shared resources) sayed:
The ECB, CCM, and AAR share the same...
Assuming SDK 12.x
For those people that want to integrate the Buttonless DFU service to their app, which uses already one custom base 128bit UUID, please make sure to:...
I need to add connectable beacon advertising data instead of normal advertising for proximity profile example (NRF52 DK -> PCA10040 ->S132 -> nrf52832).During Advertisement...
Hi,
We had a power issue with our custom board related to DFU updates. After performing a DFU we were seeing 8mA idle current, and when we had programmed the firmware directly...
