Background - We are laying out a new board, upgrading to the nRF54, and wanted to use p2.02 and p2.03 as serial UART lines because p1.04 and p1.05 were planned to be used...
Hi there,
I have recently upgraded my software to latest ncs 3.2.0. I have noticed that my initialisation does complete but it ends up with fatal error that seems to be...
Dear Nordic,
I am debugging a custom hardware with a nRF7002 on-board, using wifi shell app. At this moment the shell does not work as expected, needs to locate where the...
I am attempting to install nRF Connect SDK along with VS Code on an offline machine for development. The main two issues I have are:
The NRF Connect for VS Code plugin...
Hi
I am using the nRF54L15 DK and build a thread continueing monitor the data rate in 1 Hz, if it is lower to 800kbps I want to change to 1M; while above 800kbps I want...
Hi all,
I’m Bruce — first-time poster but have been working with the nRF9160 on and off for a while now, mainly in outdoor, power-constrained telemetry and monitoring applications...
I have a simple GATT server application with two characteristics, RX and TX. In my prj.conf, I am trying to disable pairing as follows :
I can connect to the server from...
I am trying to look at power consumption for very basic use cases to understand how often I need to go into SYSTEM OFF state. I have a development board and am measuring current...
Hi,
Is it possible to to switch between beacon mode and DFU mode (DfuTarg) without the need to press the button e.g.: by using DFU characteristic?
Is nRF51822 Beacon v1...
Hello Everyone!
I want to program nrf51822. I'm using open OCD 0.9. I created openocd.cfg file:
source [find interface/stlink-v2.cfg]
transport select hla_swd
set WORKAREASIZE...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I've downloaded S130 SoftDevice and found an example s130_demo_app which contains a project file for Keil v4, but when I am trying to open it in Keil V5 (that is the only...
Hello -
I'm not having any success using my PCA10024 as a dongle for MCP. Here is what I'm doing so far....
Remove PCA10024 jumper from P0.30-GND.
Connect PCA10024...
Greetings,
I am trying to minimize my BOM line items. Can C10 decoupling capacitor stated as 47nF/X5R on the reference design be replaced with 100nF/X5R without consequence...
Hello,
I know that this question was here before, but I've read all of the questions and answers and still I don't know what I do wrong.
I'm using 3 PWM channels to...
Hi,
I modified the uart_example project for the pca10001 board of the nRF51822 evaluation kit to make it work with a UART TTL JPEG camera. So far, the camera can receive...
Hi,
There was a thread about using PAs (and not LNAs) with the nRF51 a while back with some good advice.
One question I still have: is there currently any way to support...
The nRF51 Series Reference Manual v3.0 notes the potential need to set the OVERRIDEx registers in the radio mode to values from FICR.BLE_1MBIT to meet deviation requirements...
hi, i am working on a project which needs a relatively accurate high frquency clock. when i ran my program without softdevice, the HF clock's accurency could fullfil our requirement...
I'm trying to update the 51822 beacon example to work with iOS8 (iBeacon).
So far, I have registered to get iBeacon license from Apple, and setup the tools for compilation...
As the title states.
The DFU controller for OTA updating of the nrf series is described in the documentation of SDK 6.0. It is possible to flash the nordic USB dongle with...
