Using nrf sample from v2.9.1/nrf/samples/crpyto/rng Configure build with v2.9.1 SDK/Toolchain Configure build with board target: nrf5340dk/nrf5340/cpuapp Add MCUBOOT support...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hello,
I am currently using nordic connect sdk version v3.0.2 which seems to be the latest release on github. I am using https client example. As per the requirements...
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi,
I made a custom board with nRF54L15. I do not have a spectrum analyzer, so I cannot tune how much power goes to the antenna or how much is radiated. So, I started ADV...
Hi,
I am working on the heart_rate_collector example code of nrf51-ble-driver_linux_0.5.0.
When I use "sd_ble_opt_set" to set channel map as below, the API will retrun...
Brand new PC running windows 10.
Installed all of the necessary drivers (J-Link 5.12f)
To clarify any tool that tries J-Link connect crashes.
Also same behaviour with...
Im having problems running DFU serial examples.
i use one of the examples of the SDK but it seems like board doesnt leave the bootloader mode and memory value doesnt change...
Does someone could tell me where can I find information on the sequencing of events BLE_EVT_TX_COMPLETE and packet transmissions during connection periods?
In my application...
Hi,
I am using nrf51822 evaluation kit, and the sample program i am working on is ble_app_hrs.
I have created 4 characteristics with notify property and also created...
Hi every one,
I'm working on a custom broad and I'm trying to setup a gazell based protocol.
I had a solution using soft device and BLE which worked fine but we want to...
Hello,
I'm a few novice in BLE, and I've got a problem.
I'm using a custom project based in UART example. I'm using Nexus 5 and nRF ToolsBox for text it. I'm saving...
Hi! I want to send the temperature data that I get from the beacon sensor not one by one but in packets for example of 100 samples. I have followed this tutorial devzone.nordicsemi...
Hello,
I am trying to get SPIS EasyDMA to work. Currently the SPIS MISO response with high when the CS is pulled low by another master device, but no correct data present...
I'm trying to add more buttons to the nRF51 DK.
But I get an error.
I have found the NUMBER_OF_GPIO_TE define.
#define NUMBER_OF_GPIO_TE 4
How can I handle more...
Hi, is there RSA-512 cryptography (or maybe another asymmetric cryptography system) implementation for nrf51 or some implementation that can be easily ported to nrf51?
Hi. I played around with the MQTT example on nrf51822 module.
I get it connected to an openwrt device and can connect/publish to mosquitto on button press.
In next step...
Hello all
If you could please point me some directions on how to solve my issue, I would be grateful:
Some background info:
SDK used: 9.0
spi master code =...
Dear Nordic Developer Zone,
I have a silly question. After searching in the Nordic and Bluetooth documentation, I didn't find what CCCD and SCCD mean. Theses metadata are...
I had a design on 4-layer PCB with nrf51822, then the requirement was changed, then the 2-layer is sufficient for routing.
But I thought 4-layer PCB is better for RF circuit...
