Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
If I write a zero to the output register, and enable the pullup on the same pin, can I switch between driven low output and input with pullup simply by settting/clearing the...
Hello,
For our DFU solution we would like to read the current hardware/software revision of the module. But now we can only test the hardware/software revision of the application...
Dear All,
I can read two different ANT sensors sucessfully with my target system, but initialization of sensors only works first time. When changing sensorIDs of simulator...
HI, All.
I have some troubles:
Why MBR is erased when I erase or write the SorfDevice with 1kB at address 0x3000? My SorfDevice version is 7.1.0.
Thanks all.
Update...
Hello all,
When I try to implement the new watchdog driver it keeps saying that the NRF_DRV_WDT_DEAFULT_CONFIG is undeclared. What am I missing I have all the requered...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
hello,
In order to develop a project on master-bridge-slave,i found scan_start() in the ble_central program.But the function definition for sd_ble_gap_scan_start() in scan_start...
I am using nRF51422 SDK v8.0 and the board for evaluation is PCA10003. As I am using the BLE in GENERIC_KEYRING. The same I am trying to configure to send Immediate alert...
Hi,
I'm wondering if there's any way to check if a peripheral device was actively scanned? I can easily set my own scan response data but is there any message generated...
Hi all,
As i understand from useful discussion here, we can send one 20 bytes packet per connection when we use S120 to S110 direction, and this number could be increased...
Hello,
Working on my own code to integrate an arm chip with the nRF8001, after I read the device status, which says it's in Setup-mode, I'm sending the setup configuration...
Hi,
I want to know how sd_ble_gap_rssi_get API works? Is it send any BLE packets over radio to get RSSI whenever application calls this function. What are the sets of events...
