Hi, I am running openthread on the NRF54l15 DK. Whenever I am debugging and hit the breakpoint or pause the program, then on resumption my app crashes. How Can I debug while...
Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hello, I’m working with a combination of nRF5340 + nRF7002 + NPM1300 , and I’ve only changed the I2C pins connected to the NPM1300 to sda pgio1.4 and scl gpio1.6 .
SDK...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
Using the peripheral_uart example routine from the NCSv3.0 library with the 54l15 chip.
1. compilation command: west build --build-dir build . --pristine --board nrf54l15dk...
I am new to programming both the nRF518122 as well as the Cortex-m0. As I have been building and running the example apps that come with the nrf51 sdk, I run across the CMSIS...
Hello,
I'm developing device application where I need:
peripheral (advertising also when in connection)
central role
whitelisted connections
maybe some encryption...
Hello,
I'm trying to do some simple printfs to hyerperterminal as a way to debug my code. I have used the uart example init code but nothing prints:
void init_uart(void...
I have enabled data ready interrupt bit and also enabled the fifo bit and also enabled gyro_fifo and accel_fifo bits in mpu6050 so that when data ready interrupt occurs the...
I have a nRF51DK. The Softdevice on the board is S110.
I load the ble_app_template from the SDK 8.1 on the chip. It builds with success. Now with the MCP I am able to see...
I'm now using the lastest SDK 8.1.
I found that if I call app_button_enable() after app_button_disable(), app_button_enable() would not function again.
But if I changed...
Hi all,
I read that the nRF51822 comes as a blank chip from the factory, and this means that we have to program the SoftDevice ourself. I am wondering if this is the only...
Hi,
I'm using the Rigado BMD-200 Eval Board with sdk 8.1 and am running the ble_peripheral example titled ble_app_uart. I am using my iphone and the nRF UART app to communicate...
If using the button handling library the #define GPIOTE_CONFIG_NUM_LOW_POWER_EVENTS needs to be changed to add number of buttons being handled.
This wasn't clear to me...
Hi,all. i want to set tx power use interface "ble_tps_tx_power_level_set",and read back tx power level used tps servoce on my phone.how to do that ?Thanks for your reply!
Int the website:
link text
FEATURES show the nordice nRF51822 has 3 data rates (2Mbps/1Mbps/250kbps).
But , I set
number of packets transmitted per connection...
Hi,
If I want to run a blocked task e.g. write 1MB data to the external flash size 8MB(NVRAM), that it takes 3 seconds. What is the best way to to in NRF 51822?
Do you...
Hi,
I'm using the softdevice s110.
The power consumption is sometimes a little weird (around 1 mA). I think that the chip is in debug mode.
How can I know if the chip...
Hi,
The datasheet for nRF52 has pin assignments for QFN-48 only at present.
I'm using WLCSP package for the nRF51 and would like to know if there is any pin-to-pin compatibility...