But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hi
Here's what I would like to do: I have a bluetooth device with an nrf51822, with which I gather some sensor data, with a period of say 1 minute. I would like to store...
Hi,
If the bootloader is allocated 16 kB of flash, can it be upgraded Over-The-Air to a larger size bootloader at a later point, or does that require flashing the device...
I am a beginner and I am trying to generate a data ready event and after that reading the FIFO_Count but FIFO_Count gives me the value 1024 that is the maximum possible size...
Hello,
We are in interaction design in a school in France and we must create a connected object. We bought a BLUETOOTH SMART BEACON KIT (nRF51822) and we would know what...
I used nrf51822_narrow module DT26.
softdevice : s110
application: ble_app_hids_mouse
sdk: nrf51_sdk_v6_1_0
Now , we are able to move the cursor with the mouse of the...
Hi,
In the nRF51-ble-bcast-mesh example, it is mentioned that "handle_count" refers to "The maximum number of handle-value pairs available to the application. May not be...
With reference to the IoT SDK for nrf51, I see the APIs and examples of either server or client.
In order to create mesh or peer-to-peer, which API should I use? Or do...
In the description of nRF51-ble-bcast-mesh, there is mentioned that there could be up to 155 mesh values:
There may be up to 155 "Mesh value" characteristics in the mesh...
Hi,
I'm wondering why I can't see any packet from example led_mesh in your's sniffer?
Theoretically it's only Nonconnectable Advertisements or I miss some information...
What will be the price of nrf52 chips compared to nrf51?
Will there be any cheaper version of nrf52 chips with limited capacbilities (e.g. less flash, ram)?
I was trying to setup a GNU toolchain on Windows and use the nrfjprog utility, but despite having installed the J-Link drivers (4.78), nRFGo Studio as well as the nRF51 SDK...
I cannot seem to get pstorage working using the S210 softdevice. I can get it to work using the S130. I was not able to find any info on pstorage using S210.
I used the...
Hi
I want to use the nRF51822 to do the BLE product.I have read the datasheet of nRF51822.I have some questions:
1、Can the I/O of nRF51822 support 4.5V~5V input?
...
