We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi Nordic Expert,
Recently I wanna run ble_nus service on my nrf51822 platform, you know, sdk 6.0 does have this demo code in s110 directory, but from sdk 6.1 I cann't...
I'm trying to connect to/program my nrf51822 module I just got. I've got it set up with my st-link but whenever I try to flash the device I keep getting: Error: Flash Download...
I'm trying to enable basic commands with my device. Ideally I have a terminal open on a mac running nodejs or use the UART subapp in the nRF Toolbox App, type a special command...
What's the proper way to debug what's causing my eval board to reset? I'm assuming I need to put a breakpoint in the hard fault handle, but how do I trace that back to the...
Hi,
as a university project, I am currently developing a ultra-low-power temperature and barometer sensor powered just by RF and laser-beam energy. Please see this link...
Is there any document that describes what has to be done in the App code to migrate from i.e. SDK v7.2 to the latest 8.1.1? I could not find it.
Ideally it would be nice...
I try to add a custom characteristic value's UUID. I couldn't find any example or document that provide this information. All I can find is a function sd_ble_gatts_descriptor_add...
As I run through the examples for the nRF51 S110 SDK , I'm not seeing anything for communicating with a sensor over I2C.
On a secondary note, since I have the option to...
I am using a nRF51422 (SDK 6.1.0 with S310) and i have a question about th UART.
I can send and receive data from/to an other MCU but i have to set different parameters...
Hi,
I recently started learning to program nRF51 development kit. I followed most of the examples listed in the forums but I am unable to find a dedicated link which would...
Hello,
I have made some modifications to the OTA DFU bootloader provided by nordic and would like to some advice. I went down this design path before nordic released the...
I was disappointed to see from this question that when calling sd_ble_gatts_characteristic_add(), the value of the characteristic is copied to the SD's memory region:
devzone...
Can anyone explain what that error code is meant to mean?
With the example sdk7.1 dfu bootloader, hrs_with_dfu app built unmodified and sd110 7.1, I get this error on attempting...
Hello,
I have a BLE application running on a nRF51822 chip with the S120 softdefice. If I use the standard Android "search for device" mechanism for Bluetooth devices,...
