Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi I am not sure on the nRF51422 chip the iBeacon function is fully supported, is it ?
I can make the examples working on it but on the Nordic site only on the nRF51822 chip...
Hello,
we are trying to avoid using code that triggers hardware issue #39 in the nrf51822, which appears to be fixed in chips whose build code is Hx0.
We would like...
Hi,
I'm currently developing a firmware running on nRF51-dongles (PCA10028). The dongle communicates with a PC application over UART. Everything is working fine except...
Hello we would like to use the Nordic chip to send wireless messages from a node to other nodes directly,without hubs. We wouldn't like to be limited to up to 8 nodes receiving...
Hello,
Setup: Android 4.4.2 (LG G2), nRF51822 peripherial.
I noticed that once in a while when trying to connect to my nRF51 based device it won't connect and what is...
softdevice 8.01,app is hts. ceilphone is HTC one. nrf tools.
add some functions display，adc, eg. use nrf tools HTM connect to the board, it's reboot every time when clip...
I'm using nrf51422, SoftDevice 310 and SDK 6.1.0, when i call sd_ppi_channel_enable_set, it causes SOFTDEVICE_NOT_ENABLED error, but softdevice was enabled earlier with SOFTDEVICE_HANDLER_INIT...
Dear all.
I have some test result on DFU feature. Please any comment on this issue.
test condition
Mater control panel (64-bit version)
nRFgo studio...
In my application, I had these lines.
nrf_gpiote_event_config(0, mPinDat, NRF_GPIOTE_POLARITY_LOTOHI);
nrf_gpiote_event_config(1, mPinDat, NRF_GPIOTE_POLARITY_HITOLO...
Hi,
On iOS, is there any way to download files right into the nRF Toolbox "User files" ?
This would be useful for DFU tests, to retrieve my binaries from the web.
For...
Hi everyone,
When I set the radio's transmit power, I can use "sd_ble_gap_tx_power_set" function. If I want to get the radio's transmit power, is there any function I can...
I am using NRF_GPIOTE->EVENTS_IN[0] and NRF_GPIOTE->EVENTS_IN[1] in my software. I had my own GPIOTE_IRQHandler working.
Today I am adding UART module into my source code...
