Hi,
Developmente setup: Windows x64, nrf connect for vs code, SDK and toolchain versions 3.0.2.
I was trying to build a proyect for a custom nRF5340 board when I encountered...
Hi,
I am getting randomly incorrect SOC reported by pmic npm1300. For most days, it reports correct SOC but then all of a sudden it starts to report incorrect SOC even though...
Hi,
I recently found out about the Periodic interval feature on GRTC CC[0] and it seems like it would be quite useful for my application. Most of my code so far uses the...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
I'm trying to implement a fall detection feature on the headset side using the LSM6DSOX IMU sensor. The IMU is configured successfully, but the board halts after the INT1...
I am using the S312 protocol stack on nrf52810, with both BLE and ANT+enabled, to transmit heart rate. It can be used on most devices, but it is difficult to connect to 'wahoo...
I have a ready hogp struct and I'm trying to subscribe to an input notification (I'm connecting to a bluetooth keyboard) and I'm getting error -22. Here's the callback in...
Due to some constraints in the manufacturing process of my product, there is substantial mechanical variation in the BLE antenna. I can constrain this variation to a degree...
Hi,
I am trying to program MDBT40 with Jlink and having some problems.
Here is the scenario:
I have two versions of the MDBT40. One that I took off a BLE NANO (RedBear...
Hi,
I tried to get the sample ble_app_uart to work on NRF51422_DK with the S130.2.0.0 soft_device.
The compilation and programmation of the board is OK.
The soft run...
Hi all, i recently posted some topics about my application to receive support, everything went good but now i need to add a last step to the project, and i would like to have...
I am using nordic_sdk_10 for PCA10001. what are the BSP changes and config changes needed after replicating PCA10028 for DFU over UART.
I just changed CFLAFS & ASM FLAGS...
Hi,
I am storing data using pstorage module but when i power off my nrf51-dk board, the contents get deleted and not retained in memory. What could be the reason for that...
Hi,
For a new design with nRF51822-QFA, planning to use Johanson Balun and Chip antenna as shown in attached diagram. Not using any tuning components between Balun and...
Hi,
I was wondering why DFU_IMAGE_MAX_SIZE_BANKED is calculated as
(((DFU_REGION_TOTAL_SIZE/2) - DFU_APP_DATA_RESERVED))
and not
((DFU_REGION_TOTAL_SIZE - DFU_APP_DATA_RESERVED...
Hi, I'm using ble_app_uart application from latest nRF52 SDK on IAR compiler 7.1 and PCA10040 board.
It loads and runs debug code, but it does not add breakpoints on any...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Heading ##Here my PCA1000 board is getting detected in nRFgo studio even i can program and debug it, But i cant see COM PORT.
Can anybody help me out in this...
When i...
Hi,
I'm trying out the nRF52832 with kit PCA10040 V 0.9.0. I have S132 softdevice installed and running the ble_app_pwr_profiling example from nRF5 SDK v11.0.0.
I'm...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
