Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello,
I’m having an issue with my setup: I have a nRF9160 running the bt/peripheral sample through a nRF52840 (running the hci_lpuart sample). It seems to work fine with...
Hello,
I am using nrf52840 MCU.
I am developing a product which have 2 I2C and 2 SPI interfaces. All the interfaces are on different pins.
I developed this thing with...
Hello all,
I am using the nrf52840 MCU and NCS v2.6.2 for my application development. Here I am using SPIM3. I am using a peripheral which have an internal FIFO. From...
The partition config for ZBOSS is set in different locations in NCS. For us this worked out magically in the past because the values that were written have been the same in...
I am using the nRF51822 chip. The RAM memory is composed of two blocks (0 and 1) of 8kB each, divided into 4 sections : Call Stack, Heap, Application, and SoftDevice.
If...
Hello,
I have migrated to the latest version of the sdk11. However, I get a nrf error 4 when I call sd_ble_uuid_vs_add. Multiple people on this site have been having this...
I am trying to port blinky_blank (no SoftDevice) to my target and started by creating a custom_board.h header file with correct GPIO pins for the LEDs and duplicating blinky_blank_pca10040...
Can anyone help me reading IO capability in Android? Basically there is a known bug in some Android versions across different manufactures where Android reports wrongly IO...
I want to use chacha20 cypher to encrypt and decrypt a 64 byte message and send it over BLE. I tried using wolfSSL, cifra both of which provides the implementations but there...
Hi,
To measure the transmitted RF power (to reach EN 300 328) we Need some ATT commands to set fix channel and maximal output power. In additional we test the EN 55022...
In this previous discussion on minimizing power consumption on the NRF51-Dongle, it says:
You are using evaluation kit or
development kit and LEDs are connected
on...
My system is a BLE peripheral with 2 states. There is a characteristic that represents the state, and it can take 2 values: 0 and 1.
You can read the state, write it (force...
When the supply voltage drops below 0.6V and then get back to 3.3V the nrf51822 starts up in an undefined state and often some flash pages are corrupt after that. Is this...
Hello,
We're currently running softdevice s310 v2.0.1 with SDK 7.1.0 on the nRF51422-QFAAE0 (ie. rev 2). We're planning on upgrading to the nRF51422-QFAAF0 (ie. rev 3)...
Hi!
I was using SDK11 alpha previously and when the official version (89a8) got rolled out I started integration. First thing was the missing S210 and S130 softdevices...
Hi together,
I'm using the NUS example (NRF52832) for client and peripheral, which is running quite well. My goal is to inform the peripheral application when notification...
Hi,
I am using nrf51822 chip and i have compiled the TCP Client example from IOT SDK in eclipse.I am using Master control panel as a central device to discover the device...
I want to measure a current consumption for the 3rd-party evaluation board which has 32MHz crystal and 32KHz crystal, and there is not PO.18 on the 3rd-party evaluation board...
