Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hi All,
Can one safely assume when sending a packet to a destination address using the ping command in the CLI, that the payload echoed back is the payload transmitted...
mainc.txt
we can use INTENSET to enable certain events on the radio as in line 460 in mainc file attached. But how to enable this on the radio as a whole.
I basically...
Hi Nordic,
I am trying to enable the DC/DC converter on a QFAAH10 (revision 3) .
I am using the s130 v2.0.1 SD .
----------
1. sd_power_dcdc_mode_set(NRF_POWER_DCDC_ENABLE...
Hi,
If I configure the radio notification to ACTIVE and then set a DISTANCE of 800us, is there any way that I can configure PPI to toggle a pin for example?
I know that...
We are applying the CE certifcate for a product using nRF51822 and softdevice S130. Certification lab requires us to fill in below techanical questions. Please help to answer...
Hello, my program stuck at these assembly codes:
I decided that it was stuck because I keep pressing F11 and it just go around in circles in these 4 lines.
So:
...
Can't I connect to device that hasn't been discovered yet??
I'm trying to connect one device( A ) to another device( B ) which ADDRESS is known but never discovered yet...
Hi there,
We're looking at doing something with beacons so that we can make use of the way iOS handles scans for them in the background differently to other peripherals...
The debugger does not work with the latest GNU toolchain for ARM Cortex-M build. It throws the following error on Eclipse:
Could not determine GDB version after sending...
GPIOTE Library makes my Board(nRF51422-QFAC) Brick??
I just build my nRF51422 Board, and It's pretty working well before I've used GPIOTE Library.
Before using GPIOTE...
Hi everyone,
I am seeing an issue where the SPI (master) ignores the first byte of RX buff and begins storing the received bytes from RxBuff[1] instead of RxBuff[0]. In...
Does anyone know if there is any documentation of nrf51822's current consumption? Perhaps, something similar to CC254x's Application Note . I'm mostly interested in the current...
Hello,
I would like to build two boards that can send small messages between them, at long distance. For that I would like to use some of your devices (I used 51822 in...
Hi
I have working module which communicates via uart with another module. It works good, unless it is heated to 40C. After that temperature UART communication is not correct...
