I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
I am using the esb_tx example on an nRF51 DK board modified to send BLE advertising packets at 1 KHz.
I am receiving the packets on a BlueTooth sniffer. The contents of...
Hi,
i'm designing a board based on NRF51822-QFAC chip and i'm using this antenna chip 2450AT43A100E and this balun 2450BM14E0003T .
I put the balun as close as possible...
I have __asm("BKPT #0\n") in my code. When running without a debugger, it seems to generate a hard fault exception (which I can tell because I have a hard fault handler that...
This week I worked myself to a series of what seemed to be problems boiling down to one issue:
The Notification Write Response is lost when bonding has to happen first. ...
I'm trying to save power on my HID keyboard application by disconnecting the Bluetooth link after some time of inactivity. As soon as there are keystrokes to send, the device...
The question has been answered before, but the answer references a document called nAN-29 at this link: www.nordicsemi.com/.../73843444 . Which doesn't seem to be working...
Hello,
We use the PCA00031 dongle running the MEFW 0.9.0 in our production environment to validate a sensors accuracy. The PCA is controlled by a C# test program using...
Could someone explain the pin numbering scheme in regard to the interrupt setup handler?
To be specific, what pin number should be passed to nrf_drv_gpiote_in_init for...
In the ble_app_att_mtu_throughput example for the PCA10056 I am getting a "fatal error in the include chain" pointed from the #include "amt.h" line in amts.c. Specifically...
Hi,
I'm working on a firmware that is used in a nrf51822. I discovered an unwanted behavior of my system.
When the system is in power_manage mode, it can wake up in two...
● device : nRF52832
● sdk : 13.0.0
● softdevice : 4.0.2
Hi,
I have a problem with change mtu size.
I changed mtu size in sdk_config.h, but android application can't read...
Hi,
I am working on custom Board with nrf52382, I am using the mma8652 accelerometer for different functionality(prior is single and double tap detection).
Initially...
Hi,
Because of the compatibility issues I'm trying to use SDK10 for my nRF51422 device,
the problem is that I have flashed the S130 softdevice and the ble_app_uart, and...
I want to use FDS in my application. Lets assume I do not have a bootloader. This is part of my linker script describing memory regions.
MEMORY
{
FLASH (rx) : ORIGIN...
