Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hi all,
I have some question with ble_ancs_c sample code.
SoftDevice: nRF51822 S110 V8.0.0
SDK: nRF51_SDK_9.0.0_2e23562
I add ble_ancs_c_request_attrs function...
Hi
After reading different threads I figured out that I can program my Smart Beacons kit using NRF51-DK. Correct?
And to do so I need TC2030 tag-connect cable?
If yes...
I am using the spi slave example code from SDK 0.9.2 and connect the board to an Atmel SAM4S who is the SPI master. I can see that every time the CS signal is released from...
I want to make nrf51822 with accelerometer.But Keil compiler dont know.What I do?
It was given as examples of programs I want to do. devzone.nordicsemi.com/.../.I
I want...
Hello Guys,
I want to go with nordic solution for the bluetooth low energy application. Can anyone please explain me how much it will cost to develop your own module including...
hiii....
i am developing a custom profile with five services... i want to make these 5 services and its characteristics available only for some authorized devices.. ie...
I am working on a custom service using and nrf51822 device. SDK7.1 SD7.1
My security parameters are as follows:
#define SEC_PARAM_TIMEOUT 30 /**< Timeout for Pairing...
Hello,
I am running the UART app example in SDK 0.9.1 with the nRF52 and PCA 10036. I am using putty to send and receive messages, as well as the nRF UART v2.0 app for...
Hi,
I'm currently trying to determine the power consumption of my nrf51DK during different states of my program using an oscilloscope. To do so, I am using an external power...
We had been trying to use SD 7.0 with SDK 6.1.0, but realized our libraries were mixed up and not controlled very well, and we were experiencing occasional crashes where the...
Hello,
I'm looking to find a way to send a 32 bits number to the ledButtonDemo with the Master Control Panel (I have the Nordic dongle).
Indeed, I replace uint8_t led_state...
Hi,
I have a question regarding the NRF 52 boot sequence.
When we first receive it from Nordic, what are the boot options? Are there any other options to load a code on...
Hi,
I'd like to know how to set/alter passcode when pairing happens. I looked a few examples in Keil_v5\ARM\Pack\NordicSemiconductor\nRF_Examples\8.0.0\ble_peripheral but...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hi all,
If i have connect a band with my phone, then i let my band close to my notebook and let my notebook unlock.
Any suggestion about this?
Thanks in advance
