Hi: The device shows successful reconnection, but the mobile end is not connected.
And the connection information displayed on the device is (public), which is actually...
I am trying to measure the 300mA system current.
I cut off the system lane and connected Vin, Vout.
And when in ampere mode, the system is not turning ON.
(When I replaced...
Hi Nordic,
I have a custom board using a Raytac MDBT53 module with nRF5340. The board is designed for 3.3 V / LDO mode, but during bring-up I likely flashed firmware/configuration...
Hello Nordic support,
I am using two nRF54L15 devices with NCS v3.0.1 and ESB DPL at 1 Mbps. Auto ACK is enabled, the payload is 252 bytes, and the retransmit count is 9...
# SoftDevice Controller assert during DTM receiver test at dead/marginal RF link (nRF52833) ## Summary On an nRF52833, running the nRF Connect SDK Direct Test Mode (DTM) 2...
A customer implemented a nRF52840 (QIAA package) and says the output power is about 10dB lower than expected. Having done multiple nRF52 designs with good results, I reviewed...
While configuring a scene, the blind device is not visible in the scene settings screen, so it is not possible to set or save the blind position as part of the scene.
Steps...
Hi, I'm recently concerned with the latent risk that nrf51822 might be hacked by extracting the firmware also known as "snarf"ing.
And I know there is Memory Proection Unit...
I followed the guide of github.com/.../nRF51-ble-bcast-mesh to try the mesh with NRF51822.But there seem no discribtion about which softdevice we should use.I loaded the s110_nrf51822_7...
Use SDK6.1 / SD7.0, iOS9 can not pairing!
dm_ble_evt_handler() return error "BLE_GAP_SEC_STATUS_UNSPECIFIED"!
It is the captured packets file: ble_proximity_ios9.1.pcapng...
I can't find an implementation for the indoor positioning service in any of the SDKs. Should I assume it's not implemented? If so, are there any plans to implement it?
...
Hello,
a presentation given at the nRF52 Global Tech Tour stated that one of the planned features for S132 and S130 was a support for multiple peripheral connections (2...
Hi
Now I'm using the S130 and ble_app_uart.I meet some problem need your help.
Firstly,I download the code to PCA10028,then it can connect to nRF UART on the iPhone5S...
Hey,
I am a bit confused with "client characteristic configuration" that is used to enable notifications (at least in Android).
To enable the notifications I have to...
The manual for my Agilent N4010A Wireless Test Set talks about a BER test based on a "vendor specific loopback test mode". This mode would allow me to do BER measurements...
Hi there,
I am starting with nrf52 and SDK 9.0.2 and am struggling with the SDK structure.
Can anyone please explain the difference between
components/libraries/uart...
Hello, I have tried to combine saadc with softdevice, but having errors during compiling. I have copied .c and .h files from saadc example to ble_hrs example, but having following...
Hi,
I have a specific application/product where in I am planning to use Nordic nRF52832.
-> There is a 9 Axis Inertial Measurement Unit (accel/gyro/magnetometer) connected...
Hi!
I have been trying for over a year to figure this out, but I am unable to, and I would hope it be pretty straight forward since OTA is already in the Nordit Master Control...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
I have a device (configured as a slave) which is connected to a relay to on/off a motor.
Now, I need to connect it to multiple masters (e.g., couple of smartphones) to remotely...
Hello Guys,
I need suggestion regarding the selection of nrf8001 ble module
Does it support OTA updates?
What is communication interface? is it SPI or conventional...
