Hello,
We have the custom board with nRF54H20. The VDD_EXT pin is used to power some GPIO ports of nRF54H20 (P1/P2/P7).
The voltage we see on VDD_EXT is about 1.3V instead...
Hi,
I want to test the behavior of Enhanced Multi-Admin added in Matter 1.4.
Is it possible to verify this behavior using a Nordic DK board, sample code and a Raspberrypi...
I’m writing BLE UART code. When BLE is not connected, current consumption is ~30 µA. But when BLE is connected, consumption increases by ~1 mA. I want to reduce the current...
Hi Sir,
As we know the nPM2100 support AA/AAA batteries, LiMnO2 coin cells (e.g., CR2032), Alkaline coin cells (e.g., LR44) .
But could nPM2100 support CR123A 1S2P?
...
I've been able to flash consistently but I finally got my nrf5340 custom board working using Hight Voltage DC/DC by setting it to UICR_VREGHVOUT_VREGHVOUT_3V0, but when I...
Hi,
I had a working project for nrf Connect NCS 3.0. I don't know what happened, but now I can't even create a new build configuration. Every time I click on "add build...
Hello,
Please forgive me for this question. I am an extreme noob. And am trying to get started with my first project.
I am working with the nRF52840 DK, and I am trying...
Dear Nordic,
We’re working on a Smart Door Lock project built on custom hardware that includes an nRF5340 and several other controllers. For firmware updates, we’ve adopted...
We get the following assertion during startup if we include uart2 in the DTS.
*** Booting My Application v2.1.0-dev-ae1ee57f3906 *** *** Using nRF Connect SDK v3.0.1-9eb5615da66b...
Dear DevZone,
While reviewing the implementation of x509_crt_verify_chain() in C:\ncs\v2.9.1\modules\crypto\mbedtls\library\x509_crt.c , I noticed that certificate expiration...
Hi
I am using nRF52840 with SDK 15.3.
I have a project where I uses FatFS to write to a SD-card with SPI interface (SPIM3). This works very well.
I am now trying to...
I'm currently working on implementing OpenThread on our custom board based on the nRF5340 along with the nRF7002. While building the project, I'm encountering the following...
I am using zephyr_nanopb_sources to add some protobuf files to my app target, and this works fine in a normal build without mcuboot. However, when building with mcuboot it...
Hello Nordic Team, I recently encountered an issue similar to the one discussed in the post .After testing multiple device types, I found that only generic switche is recognized...
Hi,
I am developing for the 54l15 using nrf connect version 2025.5.92 Last Updated 2025-05-15, 10:08:43 and it's starting to seriously frustrate me.
The nRF Connecot for...
Hello,
I'm here again because this time I need to autoconfigure (configuring from inside program, no use of any nrf app) heartbeat destination node and source node.
For...
Hi,
We are currently CE certifying our product, and the test lab requires a fixed frequency firmware for the device. Are there any generic samples for this within nRF Connect...
There is a possible typo in the nRF5340 DK documentation.
https://docs.nordicsemi.com/bundle/ug_nrf5340_dk/page/UG/dk/ext_programming_support_P20.html
In the top picture...
Hi, We developed our custom BLE electronic board based on the nRF54L15 SoC. On this project the nRF54L15 firmware setup a SPI slave interface in order to receive commands...
Are there any good tools/apps to commission/provision an ble mesh application that is NLC compliant. Silvair is a great option, but is a closed ecosystem. We are looking for...
We are using the nRF5340 and our use case makes full use of all 4 shared peripherals for SPI and TWI as well as SPIM4. We want to add UART over USB and I was able to port...
