Hi,
I purchased nRF52 DK 2 PCs. PCB labeled
PCA10040
3.0.4
2024.34
boath board are new and box packed. from first time itself. I am not able to flash the board...
Hi everyone.
I cutted PCB track shorting solder bridge SB40 .
I connected like this..
Then I opened power profile kit 2. I am using amperemeter..This is my app scrrenshot...
Hi team.
Now i'm use soc nrf5340, and the ncs version 2.9.0.
I want to encrypt my external flash using QSPI.
I encountered some problems while using the nrf connect...
Nordic Support,
My product uses the nRF52840 chip and nRF52 SDK 17.1. I have a feature request to support hosting multiple peripheral connections, each with a unique advertising...
I am working with NRF52840 with SoftDevice S140 and SDK v17.1.0.
The boot loader address for this chip is 0xF8000. I can set up one of the 'fstorage' module with the address...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hello,
I'm using low power comparator with cross detection.
It works but I can't detect if it's failling or rising edge.
Can we detect simultaneously DOWN and UP...
Hi,Everyone! Now i have the board nrf52832 and i'm trying to get the battery value and send by using saadc.
i have read the example of ble_app_proximity and saadc,and i configure...
Hello! I compiled hex file with NRF52_BOOT in mbed cli. It was programmed successfully. Mbed os version include fix to use nrf52 DFUService. Bootloader is loading correctly...
Hi Nordic guys,
we are observing a strange behavior. Here some background on the project:
we are developing a peripheral device that asks via L2CAP signalling connection...
Hi,
I would like to know, whether it is possible to use a TCXO with single output as a LFCLK source, i.e. connecting the TCXO output only to XL1, instead of connecting an...
Hello everyone, I encounter a question. I follow below link to solve the issue.
https://devzone.nordicsemi.com/question/104118/adding-pwm-to-ble_template/
I've set the...
We are currently porting our proprietary stack from the nRF51 to the nRF52.
To save on BOM we are using an external 20ppm 32Mhz crystal to synthesize a 32Khz clock (power...
Hello,
I have develop an android application which connects to BLE device and perform read and write operation, so for this i was using Android-nRF-UART .
But my application...
In the release notes for the IOT SDK (which as the MQTT examples) it says: "Once BLE link is disconnected, lwIP example applications no longer get a global prefix. The only...
Hello all,
I am new to ARM architecture with some prior experience in Arduino based application development and some FPGA experience. I have a few queries:
Should...
I'm developing a project based on the Nordik UART Service and I wouldn't use pairing as in the example.
However I have some problem when a central device is already connected...
We're targetting the nRF51822 and use the pc-ble-driver (via connectivity_1.1.0_115k2_with_s130_2.0.1 )
Currently I'm using the dev board and the virtual COM port connection...
Hello,
I am trying to move from ARM Compiler v5.06 to v6.4, but I encounter an error, which I cannot handle.
The project builds fine with v5.06. When changing to v6...
