Hi,
I want to configure P2.06 of my custom board nrf54l15 as DI. I have added following configuration in .overlay file
And configured the pin as input as follows
...
When attempting to register my nrf9160-dk device on nRF Cloud, I receive a message indicating the device is already registered. I do not know which account registered it....
Hello,
On nRF52832, I implemented a code with PWM output at P0.07.
Here is the section at my overlay:
pwmleds {
compatible = "pwm-leds" ;
pwm_led0: pwm_led_0 ...
I downloaded the ncs2.6.0 version using Baidu Cloud in the China region, then set the path in Toolchain Manager of NRF Desktop, and Toolchain Manager correctly identified...
Hi,the Nordic team.
I am using nrf54L15 to develop Matter. I have seen that the official sample programs are all equipped with external flash. How can I run Matter programs...
I am using nRF Connect SDK v2.4.0 and an nRF5340 DK set up as a PAwR advertiser. Is it possible to specify the channels to use in the Periodic Advertising train? I found the...
Hello! The PCN 219 rev 1.1 says "The new device revision of nRF54L15-CAAA is not drop-in compatible with the current revision, requiring update to PCB schematic
and layout...
Hi
I want to configure SAADC channel to work in oversampling mode, and to enable burst mode.
nRF52832 Objective Product Specification v0.6.2 says:
"CH[n].CONFIG.BURST...
Hi,
I'm looking to use the nRF51822 in a new design and would like to know if there is tool available to calculate how long it will be able to run of a battery when set to...
I can discover 6 services by Master Control Panel over Android device, but only 4 services on ios 9 device, I can't discover Gap and Gatt service. What's more, when i try...
Hi all,
we are using NRF24L01+ ic for our application .we want to have TAG transmitting and receiving end separated so we are using the two NRF ic .We want that there should...
Hi,
Does Nordic provide a version of nRF Toolbox or similar to run under Windows 8.1 (not Phone)?
If not, can anyone recommend any free general-purpose tools or utilities...
I encounter a problem to switch to DFU mode from UART when BLE is connected and one 5ms timer keeps running for heart rate sensing alg. Maybe it's the reason keeps BLE busy...
Hi,
I want to use BLE to run DFU. My sdk is 8.1.1 and base project is ble_app_uart. When I use nrfgo Studio to program softdevice, bootloader and app, It can't enter app...
I am seeing excessive current in System ON, Idle mode. I am using WFI(). I have verified that
operation is being held at that instruction by using GPIO pin. Idle mode is...
Our manufacturer received new nRF51822QFAAH0 parts. Previously, we were supplied nRF51822QFG2 parts.
According to your PCN_092-1.2 Final.pdf document, there has been a...
Hi,
I can start MCP without the dongle PCA10031 (which I have updated the firmware on) and it starts ok, but when I then plug in and select the device COM 5 - 6xxxxxxxxx...
I would like to ask how to make advertisements which are less than one second. In my application, i need to scan for devices, when i find my specific device, i start to advertise...
I'm trying to programmate a simple blinkind led project to a custom board with a nRF51822 I did. I'm using a stm32 discovery to connect the custom board throw the SWD port...
I'm trying to update my beacon to use 8.0.0 SoftDevice 110. I've downloaded the 8.0.0 precompiled softdevice hex and loaded the Keil dfu_dual_bank_ble_s110_pca10028 project...
Hello,
I'm trying to use the APP_TIMER API to have tempo, but I've noticed a problem of accuracy when using the RTC1.
I use 0 as prescaler, so the RTC1 runs at 32768Hz...
Hello,
My question based on case, I've experienced recently.
nRF device that could advertise in general mode for limited time by pressing on button and continuously in...
