Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi,
i have an custom board, using s110 and HID example from sdk9.
After i pair and unpaired few times i get an error code :err_code = 0x8010
err_code = dm_service_context_set...
Hey! I was trying to modify s132 ble_beacon example to s140 for my nRF52840 DK but I couldn't build it in Segger Embeded Studio. What is the problem with "SEGGER_RTT_CONFIG...
Hi,
I have an nrf52 with sd 132 3.0.0 and SDK 12.2 which after turning it on I can connect to it without problems, but after some time (maybe 10-15 minutes) I can't connect...
Hi,
I am using sample ble_hrs code in SDK12.0.0 over Rigado eval Kit for BMD300. After running original code as it is device doesn't advertise. After I commented out the...
I have modified the ble_app_uart to start and stop advertise by receiving command from the uart port. If I don't delete the ble_advertising_on_ble_evt(p_ble_evt); in below...
Hi team,
Iam using (\ble_tester\examples\ble_central\ble_app_hrs_c\pca10028) this example.i want to get rssi from the advertising beacon.
Iam using this functions
sd_ble_gap_scan_start...
I see on your website that Bluetooth 5 throughput numbers are given in the graph below. And the following disclaimer is given.
"Net data throughput not including overhead...
I have taken a look the APIs which the S132 supports in nRF52 DK.
However i could not find the APIs that can initiate the channel map update ,feature exchange & version exchange...
hai
i have this code to save and read some data in flash.but the stored and read data are not same. always reads zeros. how can i solve that.........?
here is my code...
I'd like to be able to quickly update the advertising data using
sd_ble_gap_adv_data_set()
and at the moment I'm doing this via a bit of a hack, as I captured the advertising...
Normally, Raw data has TYPE (0x01), TYPE (0x09): device-name, TYPE (0X07): UUID 128 bits.
However, there are devices without TYPE (0x07).
Is this also a problem?
Communication...
Considering using an nRF52 module, I'm developing using EvoThings' native plugins right now. I don't think we have the resources to do IOS and Android native apps.
Has...
I have an application where my nrf52832 acts as a peripheral and I can connect to it without problems, but after some time like aprox 10 minutes when I try to connect to it...
Hi!
I have searched for this questoin, but not found anything useful. Probably I an not using a good search phrase.
How do I determine how much space is left on a nRF51...
