I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
Greetings. This is a followup to my previous question BLE Software Configuration for FCC Spurious Emissions . I did not ask the right question there and I did not want to...
Help!! I need to implement a dc motor position control and i have problem reading the encoder (too fast). I have seen that nrf51822 has a qdec peripheral. Any suggestions...
Hi,
I wanted to know if the UART pins can cause any issues if kept connected to usb (Rx/Tx pins stable to 3.3V) and directly to the GPIOs of the nRF52, while performing...
I've come across the following situation:
We have a device (nrf52) which uses fast advertising with whitelist after it has established a bond with a single phone. When...
Dear All,
I'm kinda getting desprate and would be very thankfull if somebody could help me.
I want to get two NRF24l01+ to communicate with each other. But it doesn...
hi, all
I met a communication problem between nrf52832 and nrf24le1, I used nrf52832 as receiver and nrf24le1 as transmitter, but unfortunately，nrf52832 can not receive...
We have a sensor product that has been in the field using the nRF8001 in no security required, just works mode for over a year. Recently, we had a request from a volume user...
I am using the ble_app_uart on the nrf51dk.RX is always enabled.I want to enable TX when data is to be transmitted and then disable it again.
I am using
NRF_UART0->TASKS_STOPTX...
Is there a way on the command-line to read the debug port (DP) register or access port (AP) register for nRF52 via the the nrjfprog program?
I do not want to write my own...
I'm new to the nRF51822. I've setup GCC and Make on Windows 10 and am using SDK 11. In all the examples of the SDK, flashing the newly made hex files (using GCC) with JLink...
We are working on a project that will operate in the MBAN frequency range of 2360-2390mhz. One of our current products utilizes the nRF24L chip, and we were interested in...
hello.
Although example consumes less current when connected, in the project I made, consumption is not reduced even if it connects, what is the cause?
The service seems...
Hi,
I'm trying to write more than 20 bytes to a custom characteristic, from Android (Cordova BLE Central), but this completely crashes my App
APP_ERROR:ERROR:Fatal ...
Problem description :
When using 'Just works' pairing with LESC key exchange peer_manager doesn't allocate buffer for peer public key and doesn't pass own public key to...
Hello,
I want to know what is the correct way to use GPIOTE while my softdevice is running.
I have referred the example of pin_change_interrupt that is provided with SDK12...
