Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hello everybody,
RTC0 is used by the SoftDevice. Is it possible to use the current RTC0 counter value as a system time, so that RTC1 doesn't have to run additionally? For...
I created a service with several characteristic values. I can read the values without any problem with the Master Control Panel on my Android tablet, but reading from the...
I am working with nrf51, SDK 11, S130, Keil uVision 5 and have an Application with RTX and want to use DFU OTA.
The bootloader works with the app_hrs_dfu example.
When...
Hi, I tried to enable non-connectable advertising timeout using the macro APP_CFG_NON_CONN_ADV_TIMEOUT in es_app_config.h, but it has no effect. I test this using nRF connect...
Hello,
When I call TASK_START in SPI Master it does not start a transfer. According to registers all seems to be set.
I found what was the problem. When I called TASKS_SUSPEND...
I am using SDk 11. S130 V2.0
What is the equivalent of spi_master_evt_handler_reg ?
I just want to configure my handler to receive the interrupt of the SPI master.
Please...
Hello, I've just purchased nRF52 dev kit and I'm using ble_app_uart example from SDK_12.2 to send/receive data from one pc (which is connected to the dev kit through usb)...
I have been trying to use nRF5 SDK 12 on nRF52 Preview DK by using PCA10040 instead of the removed PCA10036. But example 'ble_app_hrs' that uses SoftDevice S132 v3.0 do not...
Hello,
I am developing a custom board using nRF52. In my previous custom board, the total current consumption is 15mA with DCDC regulator enabled. I want to reduce this...
Hi,
I'm trespassing some code of nRF51 to nRF52 (s132, SDK 12.2.0) and I get an error when I try to call sd_ble_gatts_rw_authorize_reply. This is the code
case BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST...
I'm using the beacon example (SDK 12.2.0) which I've modified slightly so that a sensor output initiates advertising for 20 seconds with LED1 flashing accordingly. I want...
Hello I was working with the Flash Storage examples in the nordic github repo. I noticed that the FDS example while it has a IAR Workspace it does not have the associated...
Hi,
I am having trouble with buttonless DFU on my application. I am working on custom hardware on the nRF51822, SDK10.0.0, S130.
When I enter DFU from my application...
I'm working with pca10028.
Then gpiote interrupt is triggered twice.
Why is this happening?
And what is BUTTONx_EXT connected to PCAL6408A(U7) in schematics?
