Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
Hi,
I was reading the procedure to prepare the NRF52 DK board for current measuring and some questions came into my mind. I understand we have to open the P22 so we interrupt...
I have set up raspberry pi 3 as a border router and programmed the the nrf51422 using the iot_ipv6_coap_server_pca10028 and could successfully switch on and off led3 and led4...
Hello,
I am using secure_dfu_secure_dfu_ble_s132_pca10040 project. Now I want that the user who has specific key can only access the nrf my device and then can send the zip...
Hello!
Does anyone know what's the maximum frequency for SPI (SCLK) for nRF52832 or SDK 12.1? I see following code in nrf_drv_spi.h:
typedef enum
{
NRF_DRV_SPI_FREQ_125K...
Can someone tell me how the DETECT signal works in the nRF52840?
This version of the nrf52 has 2 GPIO ports.
Does that mean there are 2 DETECT signals? or is there still...
Hello, I'm using the nrf UART 2.0 app with nrf51822 and I'm wondering how a line of characters is sent using this app. For example if I write 'abcdefg' does the BLE receive...
Hello everybody, I'm new to the Nordic system and the nRF52. I'm trying to become familiar with the board and I want to be able to read different 4 input pins, each one attached...
I am using Segger embedded studio 3.1 with SD132 2.0.0 and a nRF52832QFAAB0.
I have verified that I am compiling against the correct header files. This service number for...
Hi, even if I set hal_nrf_enable_ack_payload(false) on the sender (and receiver), the receiver still sends back an ACK which i can detect in the NRF_ISR(). is this normal...
Hello,
I have a pca10028 and I am wondering if I can use it also to flash nrf52 boards.
I quickly tried with rknrfgo on mac to wipe a custom board based on nRF52832 and...
Hello.
I decided to use an external solution for RTC.
Sometimes the RTC chip offers an buffered 32.768KHz output.
Can I use this output to supply the 32.768KHz to the nRF52832...
I have set up raspberry pi 3 as a border router and programmed the the nrf51422 using the iot_ipv6_coap_server_pca10028 and could successfully switch on and off led3 and led4...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
