We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hi all
I am able to do start loopback using the example of UART.
But how to send data to external modules ( like ESP32) via UART from nRF9160.
I tried this example Thread...
Hi,
I want use the BLE DFU (In SDK11) to implement software upgrade to my unit.
I want the unit to support BLE and External SPI FLASH (on board) upgrade.
My unit got...
Hi
In the mqtt_simple example there is a line " modem_configure(); " which establishes the LTE Link connection. If connecting the LTE link is not possible (for example no...
I have now removed all my experimental code and have returned to the more or less original verion of the main.c for assec_tracker, but still the application seems to be stuck...
We are using the Nordic nRF52840 on our current design. Currently, I am using nRF Toolbox -UART app on my
mobile phone to send data via 9 buttons available on the App. Everything...
I am trying to read the data of an MQ-6 sensor, which is its gas sensor, but the data I receive is not from the reading by the values it shows, if you know how to do it or...
Hi,
When the bootloader address resolves to something invalid, fds_init will hardfault. I think it should have some check and return a nice error code instead.
See an...
Hi,
I want to disable all four buttons to my rigado bmd 300 evaluation kit (pca10040 is the board config. the same as nrf52 DK ) in project ble_app_uart
I have tried to...
I'm powering an nrf52810 with a 3.3V regulator. I understand the internal LDO powers the system at 1.3 V. Are the GPIO pins and other peripheral devices outputting 3.3V for...
Hi
When I select the Generic Level server model and try to bind the app key I get an invalid model Error. I am using the nRF Mesh android app.
This might be relevant or...
Dear Nordic Support,
I am using ble_nus service on nRF52840 (BMD-340-A-R) + Raspberry Pi 3B+ ( https://github.com/IanHarvey/bluepy ). The nRF52840 is the peripheral and...
Hi,
I would like to know the I2C bus capacitance for the nrf52840. Do someone have the information please ?
My slave components are compliant for 400Khz and VDD is 3.3V...
I have gone through the tutorial on mesh experimental dimming and I was able to provision the BLE nodes, contol and dim the LED1 on the evaluation module with RTT viewer....
Hello everyone,
We are having a problem with the DFU function in our custom iOS app.
We are using DFU library version 4.5.1.
After updating SoftDevice and Bootloader...
